I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
OS in development environment ：Windows10 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
Hello Devzone,
I've been working on a system to set notifications on time ready for transmission.
The client sends a WWR package to my peripheral and I want my peripheral...
Hello,
Currently, I'm trying to flash my custom board that has nRF52832 with an uart application that I integrated buttonless DFU. I'm running into a problem where when...
1.nrf9160 is there an RF calibration parameter at the factory?
2. If there are calibration parameters, does burning mfw_nrf9160_1.2.0.zip firmware affect the calibration...
I have two devices here, So I combined three HEX files and burned them with JLink, and they don't behave the same. One starts the application normally, and one is always in...
I am using a custom board with nRF8001, where I use external interrupt from the RDYN pin to let MCU know BLE has an event. MCU can recognize these events and change the associated...
Hi,
I added the feature of the 'buttonless dfu' to the 'hrs freertos' using the SDK v15.3.0.
After programmed the built image to the EV board PCA10040, it could run normally...
Hi
I have 2 customised board with nrf52832, I wanted to communicate between 2 devices. Like to send commands like turn on/off LED from my one board to on/off LED on my second...
hi
i want to use iic in my project ,and i add iic func to my project refrence project twi_sensor.
the code of iic like this：
I call the api in the main
then...
Hello
I would like to use the extended advertisement feature of BLE 5 but I have several questions: 1. If I want to broadcast data in "extended advertisement" messages ...
Hi,
My devices are currently using NRF52832 with SDK17.0.0.
I want to communicate with my devices even when the app is killed by the Android system.
At this moment,...
Please tell me. The NRF24 transmitter is in the one pipe in channel one, sends data to the receiver without confirmation of delivery at a speed of 250 kbps. 1 How long will...
Hello.
I need some documents that i can understand what is going on on the backward when/while two devices are communicating with each other or when/while a device advertising...
We're just finishing our layout for a custom nRF52832 board. According to the "General PCB design guidlines for nRF52 series" we copied the complete nRF layout from your reference...
We recently purchased a few Thingy 52s, and we're very impressed with the simplicity!
After playing with the Thingy 52,and upgrading the FW to 2.2.0, I noticed that the...
