Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
hello,
I'm using SDK 16.0 with nrf52832, for storing some information iam using flash storage, during initialization, we are giving a starting and ending address to flash...
Hi friend,
We have a project with BLE connection. It sends out the Manchester data and the data modulates with 125KHz. Can we use PWM to do that? Will the data format be...
My platform is SDK16 with softdevice, MCU nRF52840. I used 2 pin to generate PWM at 125KHz for Manchester coding. I want them are at different pin polarity. For example, if...
Hi all,
I am working with the nRF52 dev kit and the ecg sensor MAX30003. Using MBED to develop firmware.
I am using this library and the example code from maxim ( https...
Hello,
I need to develop an application for nRF51822 that uses SoftDevice 110 v8.0.0 using SDK 12.3 and extend it to use buttonless DFU for the legacy DFU bootloader of...
Hi, support team
I need to realize two-wire uarte receiver(with low power), in the scenario there is no data come from TX in most time, so after receiving the data I need...
SDK: 15.3.0
BOARD: custom nRF52840 pre-product
Hi, I want to implement usb dfu trigger library.
but, faced with a problem.
My project are started from usb cli...
cli_agent_router and multi_sensor example with nRF5_SDK_for_Thread_and_Zigbee_v4.1.0 nrf52840
problem: The coordinator restarts occasionally, and the zed cannot rejoin until...
Hello,
I am trying to configure the SAADC for the NRF52810. I read that I have to enable it via the sdk_config.h. Here I find an entry for:
NRFX_SAADC_ENABLED - nrfx_saadc...
I have two related questions about nRF52 (nrf52832) which I have not been able to pinpoint from the documentation.
Can the 32MHz crystal connection be replaced by...
Hi. I’ve developed a custom device based on nRF9160 and now have a problem of fixing GPS signal. With the same antenna and same conditions sometimes it takes up to 10 minutes...
I've set up a timer which is firing the interrupt correctly. I then set up a second compare and linked it to the PPI to fire the ADC. The idea is to do these a few times per...
Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
Greetings!
I am using nRF52832 with SDK 16.0.0 and mesh sdk 4.0.0.
Application: light switch client with LPN features added
In one of application, I have to use...
