Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
I want to mask ble interrupt（only ble interrup other is work）for temporary time and then to enabled ble interrupt ?
how to do it?
thanks for everyone answers!
Out of 10 prototype boards, we have 3 not working well due to 32 KHz xtal issue.
7 units are OK, but the other 3 units works only when configured with internal RC osc. ...
Hi,
I have been hired to migrate an NRF51 project that has S310 to an NRF52 one on S332.
I have looked at the migration guide in detail and had some follow up questions...
Hi I am having a hard time implementing DFU using SDK12.3 / nRF52832 now. I have tried so many times, but have failed a lot and have left a log similar to the next one in...
Hi,
I am using v0.4.0 ncs sdk.
I added following in the nrf9160_pca10090ns.overlay file
I added following in the prj.conf file
I added following in the...
I made a Windows application that makes USB connection with nRF52840. You need nordic_cdc_acm driver to use it with windows 7. Can I distribute the nordic_cdc_acm driver with...
Is it possible to route a signal derived from internal clock to an IO pin? I am new to NRF micro controller. My experience has been with Cypress PSOC and in the IDE it was...
I am trying to implement a struct that will be saved in non-volatile memory. Does the dev kit have these capabilities on its own? If it does is there a guide on how to use...
Hello,
I am using secure dfu with bonds (SDKv15.3, Segger, nrF52832), it works fine however after each dfu (application only) I lose the bond information.
I have search...
I am trying to communicate with PN7150 from nRF52840 DK using I2C pins.
PN7150 needs 3.3V and nRF52840 is supplying 2.9V.
I am able to read PN7150 on Arduino Mega but...
I made a Windows application that makes USB connection with nRF52840. You need the nordic_cdc_acm driver to use it with windows7. May I distribute the nordic_cdc_acm driver...
Hi Nordic,
We're developing a product based on the nRF52810 and got the following question:
We were wondering if we can recover a board in the worst-case scenario where...
Dear all, My team want to develop a innovative product. I am following this tutorial ( www.youtube.com/watch to enable the CMSIS Configuration Wizard in Segger Embedded Studio...
I am working with SDK15.3.0 and a PCA10040 with S132. I have two questions relating to the BLE addresses as seen by the PCA10040 and by nRF Connect.
Q1 - What is the relationship...
