Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi All
I have a system with two PCA10040 boards both running with SD version s132_nrf52_6.1.0. The application is build with SDK version 15.2.
I have implemented a peripheral...
I use ble_app_hrs_rscs_relay to build a node which has both central and peripheral roles. I can do scan and adv, but when I add eddystone functions "nrf_ble_es_init(on_es_evt...
Hi,
I want to develop central code to discover services of 3rd party device and to discover their services and read/write characteristics.
As seen many examples from...
Hello,
I am working on NRF52840 DK for a project on Bluetooth Mesh. Using Segger Embedded Studio for Building and debugging.
Basically i am trying to run the examplecode...
I'm writing two 32 bit words. I've verified that the source and destination addresses are word aligned (the UICR address is 0x10001088 and the source address is 2000200C)...
hi.....
i have merged the two programs ble_uart and twi sensor ......in nrf52832 ...segger15.2
i have attached all c files and h files ...... no errors ...when flashing...
Application on NRF52DK running fine average current 2uA. After installing hard and software for the PPK power profiling kit the application draws 8 mA!
Application functions...
Hi guys,
I have a board with STM32 (mbed os) and NRF52832 connected using UART lines.
STM32 has a internet connection and NRF52832 has a bootloader and DFU service.
...
I want to send sensor data from one node to other using access_model_reliable_publish() method, but my data is too large and I'm not able to send large data. What is the maximum...
Hello,
I'm using the TWI example mentioned in the subject line and I'm trying to get the TWI signals out of my demo board (Rigado BMD-350 Evaluation board).
Am I right...
hi everyone
I have BMD-300 Series Evaluation kit featuring the nRF52832 and dongle(nrf52840).
And I`m using ubuntu via Virtual Box
I refer 'pc-ble-driver' and follow...
Hello.
I am trying to build something like this in the picture below:
so my guess is that I need mesh functionality.
So my initial questions are.
Are there any...
Hi Sir
I start development form uart cli example (uart0), now nrf52840 module will connect an uart peripheral device by uart1, so two uarts would be used.
My goal is to...
Hi all,
I try to develop a gamepad using 51822 by modifying the keyboard example code.The button works well after PC connecting the device the first time ,but when I power...
