Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
hello, I have developed nrf52840 for multiprotocol ble/zigbee.
I want to simply send & receive zigbee packet not using zboss network.
I already tested example "wireless_uart...
I have two nrf52832 boards, both being developed with SDK v11 and the s132 soft device.
Board one is given commands over UART to communicate over ESB with board two. Board...
Summary of Issue: 8 dongles are used in a test system that each dongle will communicate with 1 device. Testing can start ok but after some runs, one of the dongles can not...
According to nRF52840 Product Specification v1.0, a ll the reference circuits are designed for use with a 50 Ω single-ended antenna. Why is the calculated result by AppCAD...
What would be the best example to start with my project which involves sending sensor data to mobile phone applications using ble? i have nrf52 DK and SDK 15.0
Thanks,
We're using RTT with an 52832 and it works fairly well, really can't complain much except...
On my PC everytime I launch a debug session I need to launch RTT viewer exe...
I'm using Rigado BMD350 evaluation board. I'm printing to serial port (COM3, speed 112500) using NRF_LOG_INFO.
However, the logging does not appear until debugging is...
In a recent project, me and my team have been trying to send data from 3 PTX devices to a single PRX device (the devices are all nRF24L01+) at a constant rate of 1600Hz from...
hi all!
Like two of my predecessors, I am trying to put a CR95HF into operation. I chose the nRF52832 DK as MCU (SDK 15).
[thread= https://devzone.nordicsemi.com/f/nordic...
I changed only source clock part to internal clock and it doesn't do advertising. When I debug it, it starts to run. When I finish the debug session advertising stops again...
Hi,
I've built a custom board with nRF52832, without other MCU like PCA10040. I use a FT232RL to bridge the USB to nrf UART, flashed nrf5 uart connection firmware ble_connectivity_s132_uart_pca10040...
Hi, I using nrf52810 with custom BLE profile and 4 sec advertising + continuous RTC. Device is battery powered (750 mAh) and PMDC motor equipped. Most of time (90% of day...
Hi,
I am designing my custom board with the nrf52832, which would perform the BLE and I2C functions. I wonder what necessary and basic peripherals it needs, like crystal...
Hi,
I would like to synchronize 2 Sensors with one dongle. So the problem is that we have two sensors and we want to start the measurement at the more or less (1 ms) exact...
Hello,
I am new to BLE as a technology and have a question regarding how Peer Manager handles bonding.
As I currently understand, the function of bonding is to enable...
