I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi,
My problem that the RAM is insufficient for my project.
Please, I want to know how to set optimization configuration. By the way, my central device only connect our...
Hi,
I was trying some examples of the SDK 13 and 14 for keil but now I need to undestand how works the ble mesh.
I did the download of the SDK mesh, and there are only...
I am trying add the JSON library to light switch exemple (SDK Mesh).
First all I created a lib folder in the main folder of SDK (nrf5_SDK_for_Mesh_v1.0.0_src). Inside this...
I need to store as much data as possible in flash. And the free flash size varies from different version of the application software.
Is there a method to have the lowest...
Hello,
I'm wondering how long do I need to keep the data I want to send alive.
Here's the use case:
My data changed so I need to notify the central. Since the data changed...
I downloaded the Android App from https://github.com/NordicPlayground/Android-nRF-UART, and when I run it on my phone it does not see ANY bluetooth devices. However, when...
Given that mbed is based on RTX, has anyone used the nRF5 SDK with mbed or know if it would be an easy or seamless integration ?
Thanks for your help!
Mickael
I'm implementing Capacitive Touch sensor using comparator method.
The hardware configuration was followed exactly as described here .
The output differs depending on the...
Hi,
I tried to make a special application that includes 3 advertisements, (one with softdevice, and two others with timeslot), then i successed to
integrate all the three...
Hi There,
I'm a beginner with Nordic products and I'm taking over the nRF52840 Preview Development Kit.
My final goal is to supply with a solar cell my nRF52840 running...
Hi,
We have issues with mBed's Thread::wait() in mBed 5.7.2, which causes our interrupts to stop working. Below is a small example that can be used to test this. By removing...
Hi. In the product I'm working there is a qi and NFC antenna on the same side. I resolved the issue of the qi charger overloading the nRF by placing a 1nF capacitor in series...
I enabled whitelist in my nrf51822 device and get my phone irk address after bonding then i hardcode that specific irk to my nrf device. Now i can only able to connect my...
I am using KDeveloper to program the nRF52, so far it has been working fine, but I want to be able ofdebugging and going into breakpoints, etc. What should I set in order...
