Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
I download the nRF Toolbox app and its in swift.
My current app is in objective-C and I want to implement dfu in my app.
Is there any framework that can be used in my...
Hello,
I recently migrated to nrf52 and countering some problems
with NRF_ESB concurrently with BLE.
I started with This example which was a part of the Running micro...
The chip is nrf52832.
The SDK version that I am using is nRF5_SDK_13.1.0_7ca7556,the example that i used is ble_app_uart.
When i debug about low power,i encounter problems...
Hello,
I'm using NRF51-DK (PCA10028) and I want to be sure if I'm using the external 32KHz oscillator (X2).
I'm using SDK12.3.0. I'm running the beacon example.
In...
Hi,
Is there any tutorial already for the version 14.0.0 of the SDK (nRF52, more specifically I am using nRF52832)? I would like to know how to configure Advertising, and...
Hi
I have development kit nrf51 PCA 10028 and try to run uart example example with loopback (RX connected to TX, RTS connected to CTS). Unfortunately, after sending, I...
I'm using the bootloader_secure_ble example from SDK 13 on an nRF52832. I'm using the GCC toolchain. Here is an extract of the linker file from the example:
MEMORY
{
...
I'm running nRFgo Studio on Windows 10.
Have tried to re-install (nrfgostudio_win-32_1.21.0_installer.msi) without success..
Any idea what to do?
Thanks!
I'm using nrf52 with S132. I was trying ble_app_uart example and it is not printing any log messages into the COM. Do I need to do anything extra to make it work?
Hi there,
I am currently wondering if the following is possible?
As stated by the Cortex M4 reference manual states that a system can have 200+ seperate handlers within...
Dear all:
chip:51822
sofedevice:s110 8.1.0
the pcb is supplying for dc-dc mode,but the fireware have not open dc-dc mode.
Whether can Increase the power consumption and...
Hi,
The tx/rx sequence diagrams don't explain when EVENT_ADDRESS and EVENT_END are triggered when using coded phy:
there are CI and TERM1 fields between address and...
