Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Is there any way of instructing the BDS plug-in which optional characteristics to include in code generation for adopted services without converting to a custom service? ...
(/attachment/41972e0db37f912bba4731a3b5ffe839)(/attachment/0838bef738e72c89e2a9af90d6e3f640)(/attachment/a62ce68db8c9d23b285a9f94a5c9beac)I have been developing on the nRF51...
what should be the direction of pin P0.26 and P0.27 when external low frequency crystal is connected ???
or they should be left untouched in the code ???
To reduce the...
Hi:
I come across a problem when I debug NRF51822. I don't know how to config its clock.My board XTAL is 16MHz, and I want config is to 32MHz，Is the method below OK?
NRF_CLOCK...
Hi,
My settings are:
NRF_DRV_SPI_FREQ_1M, NRF_DRV_SPI_MODE_2, NRF_DRV_SPI_BIT_ORDER_MSB_FIRST.
I'm trying to readback 0xD8. The proper value should be 0x71. Instead...
Hi,
I am trying to use the nrf52 in serialized mode, where I was successfully able to program the connectivity board (using SDK 11.0.0) However if I try to load any of the...
We are using a module which has nrf51822 on it. Before we have programmed it, we were able to see it when we scan for ble.
But after we program we could not able to detect...
I am building an automated test stand for programming our production devices. After programming, I need to pin-reset the device to leave debug mode so I can get an accurate...
We have an BLE application that we are targeting the nRF52 device for. The application demands using a UART interface to communicate to a host processor. In addition, we typically...
Hi all,
until now, I used nRF51 Chips on my board. I programed them trough the nRF51DK(PCA10028). But now I would like to work with nRF52832 Chip. I have a nRF52DK(PCA10040...
hi ..
i am new to mbed and nrf51.
softdevice is s130
if i enable the ADC in my project then other output(out3,4,5,6) is not working ok.
if ADC is not enabled then...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi
I have a problem when bootloading with nrf toolbox. It seems like when i flash files over 0x10000 in size the program overwrites itself. When i flash files with smaller...
I know this is somewhat "how long is a piece of string". I'm happy for guidance rather than solid numbers:
I'm trying to spec a "keep alive" circuit for an nRF51822 project...
