Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
I got the Dynastream N5 kit and have successfully used it with limited ANT work and was trying to get BLE working but can't get a driver for the USB dongle. On the 51422 product...
Hi All,
I am working in the sleep mode with system off and wake up with internal RC clock.
It function well when connected to EV board...
I see the "Emulated System...
I want to write PCA20006 nRF51822 Beacon Firmware to PCA10004 on nRF6330.
I understand need to modify GPIO.
PCA20006 firmware consist of 3 firmware, SoftDevice, application...
Hi !
Regarding the dfu upgrade service of thingy52, I would like to ask if it is possible to use some Bluetooth devices (such as laird's bl654) to make thingy52 enter dfu...
Hello,I program with nrf52833,NCS v2.9.0.And there is an error happened.
In my main() ,if I place settings_load() at top, it will make my sys resetting. Cause I need to...
Hi everyone,
I’m working with an nRF52840-based device that communicates with an Android app via BLE. I’d like to know if it’s possible to use the nRF21540 RF FEM to extend...
We are looking to do DFU over UART to the Application as described in DevAcademy nRF Connect SDK Intermediate, Lesson 8, Exercise 1, Step 5. However, we have only one UART...
Hello,
I am working on a custom Agora board that includes a BT40 module with an nRF5340 MCU. I am trying to enable the MCUboot bootloader by setting CONFIG_BOOTLOADER_MCUBOOT...
Hello ,
I am getting "Configure Cmake Option visibility" notification in visual studio. I am attaching snapshot as below.
/resized-image/__size/640x480/__key/communityserver...
Hi,
I have just acquired a new nRF52 DK devkit.
Performing a `nrfjprog --recover` followed by `nrfjprog --eraseall` doesn't work to remove the protection.
I do not flash...
Hi,
I use the secure BLE Bootloader to update the nRF52840 (with S140).
Now I want to add a UARTE to update the STM32 connected to nRF52.
Do you have a solution to do...
Hello,
I am using two nrf52840 DKs to test ble transmission and i2s output. The nRF Connect SDK I use is v2.6.0.
Both of them are ble connected. One sends data to the...
Hello,
I think llpm's sample project is wrong. Evaluation board is not supposed to be communicating.
To verify the defect, the value of the time variable is fixed. This...
hello, my code was built under ncs v2.6.0 and tool chain 2.6.0 without issue, I upgrade them to v2.9.0, then I get these errors, can not figure out how to fix them.
could...
Hi,
From https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/samples/bluetooth/direct_test_mode/README.html , it writes " After programming the sample to your development...
Hi,
I’m working on enabling the asynchronous API on UART1 in the nRF Cloud Multi-Service sample for the nRF9151. Despite setting the necessary configurations, when I call...
I'm using NCS v2.9.0 and attempting to communicate with an ADXL372 IMU over SPI. Occasionally, the MCU successfully reads from the IMU and begins printing values. However...
NCS 2.7 with mcuboot via sysbuild
custom board with nrf52840, 2 custom applications (manufacturig and end-user)
In my application our DFU will be performed over BLE...
