It is nRF54L15 + SDK 3.0 + Matter application.
I have developed a custom BLE service that is based on Nordic's proprietary NUS BLE service. The BLE custom service is enabled...
Background
For reasons that I do not want to dispute here, I am building a custom bootloader for the APP + NET cores on the nRF5340. This custom bootloader is not a Zephyr...
I am testing out the nRF54H20 on the nRF54H20-DK version 0.9.1. I have followed the steps for setup in the "Getting started with the nRF54H20 DK". I currently have nrf54h20_soc_binaries_v0...
I am trying to get a WiFi project working using the nRF52840DK and nRF7002EK . I use a 3.3V power source that is supplying power to both nRF's in parallel. For the nRF7002EK...
Hi,
I'm developing firmware for the nRF52840 DK using nRF Connect SDK v2.9.2 , and I’m running into a problem that didn’t occur in v2.8.0 .
My project uses Zephyr and...
I'm trying to run the DFU sample l9_e5_sol on a custom board using the nRF5340 and SDK version 3.0.2.
My goal is to perform DFU over BLE using external flash. However, before...
I am receiving an error when connecting to a custom board by running nrfjprog --reset, any similarly with any other commands that require connection.
I am connecting through...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
To conserve battery power, my Beacon application powers an attached sensor off GPIO pin 24. That way, when the sensor isn't needed I simply call nrf_drv_gpiote_out_clear(24...
Is there any ready-made example that would show how to configure nRF52 to make analog-to-digital conversions automatically on the background, without CPU intervention between...
I have an application that currently does not use the soft device, but I want to use the dfu bootloader. The application runs fine if only the soft device is present, but...
I'm trying to use the ble_app_hrs_s132_with_dfu_pca10040 example project with my PCA10040 nRF52 DK.
Using Keil uVision 5, I'm able to compile the project and flash to the...
Hello!
When two devices, Peripheral/Server and Central/Client, try to send Notifications and Write Commands, respectively, to each other at the maximum capable rate, who...
Hi Nordic's community,
I have a "stupid" question; i search a programmer for programming a nrf51822 module, and i see everywhere : " flash SD + BL + DFU"... i know Sd ...
hi.
i use nrf51422 v2 that its sdk is version 6 that it did not have any uart over ble example .
if someone had it please give me its link .
thank you .
I'm implement some feature to update the softdevice for nrf51822. It has chance to switch s110 to s130. I have a requirement to treat the MBR of s110 and s130 the same as...
Is there any User Guide for the nrf52832?
TI has the Wiki (including the User's Guide) and the Developer's Guide:
processors.wiki.ti.com/.../CC2650_SensorTag_User's_Guide...
I have two questions related to DMA in the nRF52832
Would you please let me know if there is an example of using DMA with the SAADC?
Is it possible to use...
I'm new in development for BlueTooth. So, please, can anybody tell me, what i need for developing simple application.
I need BlueTooth connection with Android phone and iPhone...
Hi,
I'm working from ble_lbs example to extend it for more services. But if I call sd_ble_uuid_vs_add() more times (first it's called in ble_lbs_init() and second time it...
I buy NRF51822 eval-kit.
BLE dongle and did not have a compatible, The attempt to change the Stack.
But I never found the Gazelle stack.
where are gazell stack?
Hi,
Can someone tell wether Security Mode 1, Level 4 is available on the nRF52832 and SoftDevice S132?
In one PDF I found only Level 1,2 & 3 but in the S132 API reference...