Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
I use nRF52832 as a master to communicate with ads1292. then I want to config the ads1292, so i should send the register address and configuration data.But I don't know how...
Hi,
I tried to compile my own program with eclipse and GCC with c/c++.
I followed this tutorial : TUTORIAL
I have some problems :
First : i have problem with...
Hello,
I developed a code (softdevice S110 and SDK 10) on a prototype based on a NRF51822G2 chip. I tried to reproduce the prototype with NRF51822H0 chip.
I flashed...
Hi,
I use ESB protocol, and all is working fine :)
Now I want to retreive the address of the sender because I can have multiple sender in my network.
I can add this...
With there being +/- 4dBm variability in output power from nRF52 to nRF52, each device needs to be calibrated in order to comply with FCC rules. One of the rules is there...
Hi
I'm porting a nrf51822 project with S110 to a nrf52 board. In this case, I'm a bit confused about which softdevice to use. S132 it is the equivalent to the S110? Or...
Hello everyone,
I am using the nRF52832 rev 1, i am not using the softcore. When the cache is enabled as below, the performance actually seems to get worse.
F_NVMC-...
using Bluetooth Developer Studio, and
nRF52 SDK v11.0.0 - Experimental: Bluetooth Developer Studio Example
I have created a profile using BDS and generated the files with...
In order to teach a class of students using nRF developer boards I'd like to use the nRF Blinky application running on Android, iOS, or whatever mobile platform. The problem...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
Is the nRF Temp App source code available for download?
I am currently developing an ultra-low non-connectable beacon and would like to use the nRF app as a starting point...
I guess all the Bluetooth members saw the email from the SIG about the next version of Bluetooth and how it is confirmed to have double the range, quadruple the speed and...
I'm looking at table 23.15.2 in the nRF5 Reference Manual, and it states that TX startup current is 4mA with the DC-DC enabled.
Does that 4mA include the CPU idling...
My project: nRF51422, S110, based on SDK 7.1.
My project employs several application timers (run via the scheduler) and a continuously running Timer1-based 1ms timestamp...
