Hi everyone,
I'm facing an issue where MCUboot doesn't perform a swap after reboot, even though the DFU download to slot 1 completes successfully and boot_request_upgrade...
I am getting the following build errors when working with both DFU (MCUboot) and the file system (FAT FS) together. Errors: D:/ncs/v2.9.0/zephyr/drivers/disk/flashdisk.c:533...
Hello,
We are working on an audio project where we are using nRF5340 Audio DK. We want to externally interface the digital microphones without using the on-board codec ...
Hi, We want to integrate LORA LR1110 for the final year capstone project. From the documentation we have understood that Kit is fully compactable with Arduino UNO. But SPI...
안녕하세요
nrf9160DK 보드로 개발하고 있습니다.
blink 예제로 컴파일 및 다운로드되었음을 확인했습니다.
SDK에서 예제AWS_IOT_MQTT로드하여 테스트하고 있지만 아래와 같은 오류가 발생합니다.
해결 방법을 가르쳐 주시면 감사하겠습니다.
zephyr/subsys/net/libsubsys__net...
I'm trying to run Wi-Fi scanning or AP/STA mode examples on the NUCLEO-U575ZI-Q board with the nRF7002EK shield, but I keep getting an "RDSR2 register failed" error. I've...
I have several hardware pieces based on the Fanstel WM02C nRF7002 module (nRF54L15 host) and am having problems connecting to WiFi networks on a subset.
All modules successfully...
Hi, on nRF54L15 Dev Kit, we are trying to validate our sleep current consumption. We are seeing sleep current of ~100-300uA, when it should be a fraction of that. As per datasheet...
Hi I'm testing the current consumption of the external qspi-flash on nrf5340dk [ MX25R6435F]. I have used ppk 2 to measure consumption with the dk and also have used a power...
Dear Nordic Technical Support,
I'm writing to report an issue I'm experiencing when trying to integrate MCUboot with a Zigbee R23 project for the nRF54L15 platform.
Issue...
I'm having some pretty significant issues with Visual Studio Code and the nRF Connect SDK/Toolchain installation.
I'm on Windows 10, and have been running V2.6.1 of the...
Hi support team,
We are using nRF9151 with NCS v2.7.0 for our IoT product. During power optimization, we observed:
Even after disabling UART RX interrupt using uart_irq_rx_disable...
Hi there, I am trying to find the logic implemented in a source code which performs the following steps: 1) reading from a binary file that represents the firmware image that...
Hi, we are developping a medical device that receives an audio stream from a smartphone. We have a custom board connected to a different DSP than the one in the nrf5340_audio_DK...
Working on the nRF52833DK board and based off the nrfx_spim_spis advanced non-blocking example sample. I've already converted the SPI master to use the Zephyr driver instead...
We want to use PSA crypto to generate a persistent key that can't be read out and use this for encryption/decryption.
We have of course tried the persistent_key_usage sample...
Hi all :
I am trying to use the nRF54L15 built-in load capacitor for crystal but I do not know how to measure the crystal performance, such as driving level and negative...
Hello,
I am using nrf52840 MCU.
I am developing a product which have 2 I2C and 2 SPI interfaces. All the interfaces are on different pins.
I developed this thing with...
Hello nordic community,
i have custom board that have nRF5340 and nRF7002, our requirement is to use wifi every 5 minutes (connect send data and disconnect) but randomly...
Hello,
My name is Calvin and I am tasked with testing the NRF52840. I want to create my own development board for prototyping a project, but I do not want to keep plugging...
Hi!
We use nRF Cloud Log backend in our project. And during my research I found that it actually doesn't filter (despite the filtering code is there) messages generated...
