Hello,
I am trying to use LTE connectivity on a custom board with a nRF9160 SICA B1, but i am facing issues with the modem.
With both my own app firmware and the sample...
I have searched all responses here and whatever sources I can find, but not have any success. The main problem is that existing materials appear incompatible with the 54L...
I'm pulling my hair out here. Why would syntax errors completely break the toolchain?
Every now and then ill have a syntax error which causes the build to fail, the entire...
Hi, I have test the throughput using two nRF54L15 DKs and make them close to each other.
My result is:
1. My first question would be: the best througput for 2M phy is...
Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
Hi,
We are currently evaluating the NRF9151 for asset tracking using the AT firmware on the NRF9151 evk and an external MCU for the application firmware, emulating the final...
Hello,
We’re Bachelor’s students developing a project to estimate the angle of arrival (AoA) using a BLE antenna array on the nRF52833. Our implementation builds on Zephyr...
Hi all,
I'm working with the nRF52805 (QFN16) and was curious if the nRESET pin (P0.21) can be disabled via the UICR->PSELRESET[n] mechanism, as is possible on other nRF52...
I plan to use my own SIM card (not from Ibasis). Could you clarify how to register the device in nRF Cloud to enable A-GPS services? - Should I link the device’s IMEI or ICCID...
Hello,
I have been able to get FW OTA to work perfectly well over BLE using
CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU =y
Now I am trying to display the update progress...
Hello,
I am trying to build a firmware for the nRF5340 on the Thingy91:x. The firmware should use the external flash for the secondary Image and is using the chained bootload...
We have an existing application that is based on asset tracker V2. It has been running since version 1.7.0 I have migrated to V2.9.0 a long time ago and it is running flawlessly...
I use nrf5340 DK as AP, nrf54l15 DK as TAG.
Below was uart print comments from AP
ESL_AP:~$ > esl_c bond_dump
esl_c bond_dump
Dump bonded device
ESL_AP:~$ > esl_c...
I've been working on a custom device utilising the nRF52832 that needs to switch GPIOs in tightly controlled pulses. The problematic section is part of a much larger project...
Please refer to the link below. How can I configure the Commission Flow according to the requirements?
www.matteralpha.com/.../how-does-matter-qr-code-work
hi,
I am reviewing development in the environment below.
* HW : nRF52832
* SW : SDK -> example -> ble_app_uart_c
In the nRF52-DK board, we reviewed the example...
Where can I obtain the security certificates (e.g., client certificate/private key) needed for TLS authentication with nRF Cloud? - Are these generated during device onboarding...
Hi,
I wanted the zigbee firmware to support BLE OTA. so I downloaded the latest zigbee SDK from the following link " ">github.com/.../pulls".But the compilation encountered...
We are developing a light product that features a built-in button. A single click of this button toggles the light on/off, while a long press adjusts the brightness level...
Hi, on nRF54L15 Dev Kit, we are trying to validate our sleep current consumption. We are seeing sleep current of ~100-300uA, when it should be a fraction of that. As per datasheet...
Hi I'm testing the current consumption of the external qspi-flash on nrf5340dk [ MX25R6435F]. I have used ppk 2 to measure consumption with the dk and also have used a power...
Dear Nordic Technical Support,
I'm writing to report an issue I'm experiencing when trying to integrate MCUboot with a Zigbee R23 project for the nRF54L15 platform.
Issue...
