Hello,
I'd like to ask what needs to be configured to enable communication between two boards: nrF7002-DK and nRF5340-DK via another UART (e.g. UART1).
Please provide...
Hi Team,
We are developing on a custom board with an nRF54L15 (Raytac Module with NRF54L15_xxAA_ENGB) and are unable to provision a pre-generated secp256r1 private key into...
Hi, I want to run Bluetooth Mesh Light example on nrf54h20 chip.
At the beginning I prepared devboard with this tutorial: https://docs.nordicsemi.com/bundle/ncs-latest/page...
Hello,
I am trying to build a firmware for the nRF5340 on the Thingy91:x. The firmware should use the external flash for the secondary Image and is using the chained bootload...
SDK: nRF Connect SDK v3.0.2
DK: nRF54L15-DK
Sample: spi_flash
default:
mspi-max-frequency = < DT_FREQ_M ( 8 )>;
If I change it to 32, it will printf these...
Hello,
I'm looking for answers and some explanation for two main questions - is it possible to perform non-simultaneous multi-image FOTA over WiFi? Is it possible to support...
As shown in the figure, MCUboot has a boot_go_hook function. I'd like to define this function in my own project and compile it into MCUboot. Since I'm using single slot DFU...
Hi,everyone,
In my project ,I want to save some data when disconnect evt happens; here is my code:
the problem is ths program always stuck in power_manage() function; what...
I'm basing my schematic and antenna design using the PCA10028 as a reference.
I'm not including the J1 RF-connector into my design. Do I still need to include both C6 and...
I only hope that their devices can link their mobile phones, other mobile phone links may not link, but I didn't want to enter a password, directed broadcast method can, about...
I am using the nRF52832 as a MCU in the wearable device,now i want to use the spi master mode to collect data and store data ,and when it is necessary,I want through the bluetooth...
Hi
I have been working with nrf8002 chip. I simply want to program the hardware in a way such that it gives out a signal that can be detected by the emulator.
Hi Guys.
I have a little question.
I leave the bluetooth smart world one year ago, and now that i want to remake some project i read that there is some new.
So in my situation...
link text from this link i have some questions
(1) when i am trying to do step by step debugging ,debugger stops at sd_power_system_off();. can you tell me what to write...
@Michael Dietz
Hi, Michael & everyone. I'm using nRF51822 now. I followed the post Segger Embedded Studio & import the beacon example in SDK 10.0.0 . In Keil, the memory...
Hi, everyone. I'm focusing on SES with OS X for a long time. But there are always some faults and I have never succeeded utill now. I used to think OS X made these faults...
Yo Man,
I use nRF52 with example "ble_app_hrs_rscs_relay" in SDK11.
The printf only send one byte and I check other people asked question but still send one byte.
So.....
I want to test the Bluetooth signal performance of NRF51822 with frequency spectrograph,but Idon't know how to set a fixed frequency to NRF51822,I need your help
thank...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Hello everyone~
I'm setting up an eclipse and gcc development environment on Mac OS X following Vidar Berg's tutorial here: https://devzone.nordicsemi.com/tutorials/7/development...
I have some questions about DTM, can anyone help me ? thanks a lot!
1. I use DUT and nRF DK module to do the test. When nRF DK module enter tx test and DUT enter rx test...
Hi,
I'm using the PCA1040 with the SDK11.0.0. For now I'm trying to communicate with the TWI as the example twi_sensor indicates. The problem comes when I try to do two...
