Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
Hi,
I have developed two different application on nRF51822 with two different location. One is start from 0x1D000 with max size of 16 KB and another start from 0x21000...
When i am trying to transfer data over air using sd_ble_gatts_hvx() function every time i am getting err_code 12 ( NRF_ERROR_DATA_SIZE ) error.
Here i can send data from...
I'm working with ble_app_uart_s130.
Compilation is fine and it works as expected in hardware.
I'm going to add application timer and scheduler.
To do that I have to set...
I want to use ADC / PWM / I2S / UART / SPI / I2C / at a time.
So, Can I use all GPIO pin assign any function?
If I can't use some function at a time, I want to know the...
Launch an example for UART (BLE PERIPHERAL) on the board PCA10040. When try to set the parameter APP_ADV_TIMEOUT_IN_SECONDS = 0 (no timeout) get returned NRF_ERROR_INVALID_PARAM...
Hello,
I have a question regarding AVDD pin.
I am using nRF51822 CEAA package. And the reference circuitry on the datasheet uses a 1.0nF capacitor between VDD and GND...
Hi everyone
I'm facing a weird problem in my design and FreeRTOS. Apparently, my system was working fine, but along I'm adding more tasks, i've detected the system stops...
I'm using RS485 driver on NRF51822 uart. I started software developing with ble_uart exapmle.
RS485 as always has direction control inputs.
Before data transfer to uart...
In my app I have the following:
s110
20 ms min connection interval
100 ms max connection interval
4000 ms con_sup_timeout
I'd like to set the slave_latency...
Hi,
The documentation states -96dBm rx sensitivity for 1mbit BLE mode and -93dBm for proprietary 1mbit mode.
Is it possible to use BLE mode (3 in MODE register) but...
I want to scan for peripheral devices in central-role and at the same time i want to broadcast in peripheral-role. How do i have to initialize the Softdevice in this case...
Hi,
I'm originally iOS app developer.
I have been developing with custom PCB that based on nRF51 chip. (not nordic development kit)
My PCB has a gyro sensor and some...
Hi,
Whenever i m trying to upgrade my application using iphone with binary file then i get "unsupported DFU" error. what is meaning of this error and how can i resolve...
Hi please help,
We are facing a problem of Gazell failure (not getting interrupt on gazell ISR) when i perform external Flash write using SPI.
If i disable gazell and...
hello there i downloaded nrf5 iot sdk. i have nrf51 and nrf52 kit.now it has many example codes like tcp,udp. can anyone tell me how to test it with my kits??
