After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I read a document, "Setting up production test using DTM", "nAN-034 Application Note v1.0".
And, Figure 3 shows how to setup test environment.
But, I cannot find which S...
DCDC_testing.zip
Hi,
I am in the process of reducing power consumption in micro esb mode. I use the following code, just for testing. The following code consumes 18mA unlike...
It is possible to load a new firmware in a NRF51822 PCBA using the Nordic Development Kit NRF51DK?
Do I need a special connector?
This is the beacon Module I pretend...
Hello,
I have a board with an RFDuino on it which uses a Nordic nRF51822 internally. We are seeing a few of them auto-brick when the input voltage dips too low.
My first...
I have a question about the usage of Flash Data Storage, chunks and parsing of the data retrieved from FDS.
How, when and why are you supposed to use "chunks" when setting...
Hello,
I would like to implement an interface with an external SPI ADC using the nRF52832.
The ADC has a RDY (ready) signal that goes low every time a new sample is ready...
Hello,
I have simple custom PCB with nRF51822.
I am trying to make it advertise like a beacon, by program it with ble_app_beacon example from nRF5_SDK examples.
I have...
I'm playing around with the experimental ble hrs with NFC pairing example, and I cannot seem to get it to work with my Android 6.0.1 Moto X Pure. I tap the phone to the NFC...
I have been trying for a long time to implement ble_uart_app with static passkey on SDK 11 s130 on nRF51-dk.
There are a couple of threads on this feature.
devzone.nordicsemi...
I am using ble_app_uart SDK_11 s130 on nRF51-dk.
I want the received characters to be buffered into a string until a new line character is received. The relevant code for...
Hi,
I am trying to attempt the RTT tutorial and I am not able to complete the first task.
I have included the SEGGER_RTT.h deader file, copied RTT and Syscalls folders...
Hi, In my project I need to read a characteristic value, I'm using nRF51822, nRF5_SDK_11.0.0_89a8197 and s130_nrf51_2.0.0_softdevice while I reading it takes around 700ms...
Hi, I'm using ble_app_uart application from latest nRF52 SDK on IAR compiler 7.1 and PCA10040 board.
When opened, it losses all "defined symbols" on Preprocessor tab on...
I am relying on the link below to implement pstorage.
infocenter.nordicsemi.com/index.jsp
I am also using device_manager in my app which may conflict with pstorage....
I'm using SDK_11 on nRF51-dk. I'm trying to use pstorage to store configuration settings. There are threads providing examples for pstorage but none for SDK_11. Which is an...
