Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Dear Nordic Support Team,
In the datasheet of the nrf9160 (nRF9160_PS_v2.2.pdf) the VSS pin appears in the section 6.4.5.1 GPIO Electrical Specification, but I cannot find...
I am preparing to make our first firmware release on our custom board, which is equipped with the nRF9160 SICA B1 , modem fw version 1.3.4 . Our application is based on the...
I've been running into a lot of issues where a change in the configuration for the application results in an answer that basically states:
"You're supposed to add this configuration...
Hi all!
I'm wondering why the VS Code has option to create a new board for the nRF5340-QKAA only?
I have on hands the nRF5340-CLAA and nRF7002 chips which I'm going to...
Hi,
I'm currently building a product that uses PSA crypto API to generate, and save some keys in secure storage. I also need to have a WiFi functionality (nRF7002), but...
I have been able to connect and initialize two different Bluetooth OBD II Devices. I am running into issues with the third device I am trying to add as an option. I add the...
Hi,
nRF54H20DK (rev. 0.9.1), SDK: v2.9.0-nRF54H20-rc2 and the same Toolchain, IDE: VSCode + nRF Connect
We need to implement a multicore application for nRF54H20. I...
Hi,
I have a question concerning time zone support in nRF SDK >= 1.9.1 for nrf9160.
I'm trying to implement an LwM2M client that should be able to convert a UTC datetime...
NCS 2.7.0/2.8.0
mcuboot + MCUMGR in the application for BLE DFU
NRF52840
We have been developing our next version of our product, transitioning from NRF SDK 5 to NCS...
Hi,
When I used NCS V2.5.0,after two devices successfully establish a BLE connection but then disconnect due to a timeout, subsequent reconnection attempts fail with error...
I have a BLE system where multiple sensors operate as peripherals and send data to a BLE central. These sensors enter sleep mode after transmitting data and later wake up...
Hello,
I designed a PCB using nRF52840 for controlling the board.
I have physical access to the following pins : SWDIO, SWDCLK , VSS , VDD , nRESET.
What is the boot...
Hi,
I'm trying to test DTM over USB CDC with an nRF5340DK unfortunately, Direct Test Mode desktop App is not detecting the DK.
Build command (copied from VSCode output...
Hi, I have encountered issues flashing a NRF52833 board which is on a custom PCB. I have picked the project up from another developer so it is somewhat developed already....
hi support team,
i want to confirm the FEM control when using nrf21540ek for mesh demo "light" with 52840dk.
i set :
CONFIG_BT_CTLR_TX_PWR_ANTENNA =20
CONFIG_MPSL_FEM_NRF21540_TX_GAIN_DB...