Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
Hello, we've a nRF9161 DK board a we saw on the back side a footprint for mounting an SD card holder and we found the SD card holder component in the BOM.
Unfortunately...
Background : To set up a Matter ICD (Internet Connectivity Device) and Thread as a SSD (Sleepy End Device). Here are the detailed settings：
Currently, the Matter over...
Hello,
We've several active products utilizing nRF52840-QIAA. Recently it was realized that this version is not recommended for new designs anymore and apparently can be...
The nrf_cloud_multi_service sampe is running in to fatal error while trying to downolad A-GNSS data. The sample is configured to work with NB-IoT and CoAP.
Here is the log...
Hi,
I am Currently running BLE Mesh with nrF5340DKs, I refer all nodes as Cores but 1 as Master, Master receives and Stores data as well send data to PC Serially for further...
I used Nordic52480 DK(bulb) as DUT to run Matter Certification case TC-DGGEN-2.1 .
Steps:
1. setup OTBR on Pi4：./certification-tool/backend/test_collections/matter/scripts...
Hi, I want to enable APPROTECT in nrf52840 using NCs 1.8.0 or 2.4.2 or 3.0.0 can you tell the process of doing it? Also I want to know the use of Access control list . Is...
Is a common ground required when measuring current in current meter way?
Can externally supplied voltage exceed 5V? Will this cause inaccurate test results?
Hi Nordic team,
We’ve implemented a custom firmware update flow for our nRF5340-based device , which supports a robust single-image FOTA process using external NAND flash...
Hi there,
i'm progrmming a Lcd over SPI but i got this failure once generate the build :
************************************************
* Executing task: nRF Connect...
So I got me one of these
and after a day of making it work on windows I was able to lunch visual code from wsl and compile. the next day I found how to make a flash with...
I have a custom board using a nRF52840.
A part of the configuration is a Analog Devices MAX98357AEWL+T Class D amplifier which is driven by i2s0.
When the board is idle...
Hi there, I'm facing difficulties configuring the Adafruit ILI9341 with the nRF52840. Are there any beginner-friendly instructions on how to configure and program it over...
I switched from segger ses to NCS for the nrf54l15. I am really surprised, that the build process takes several times longer now.
Especially, when the proj.conf has to be...
Hello,
our project which started 7 years ago with SDK13.0 has been migrated some time ago to SDK 15.3 and now to SDK17.1. At the beginning we were quite happy with the RTT...
