I'm developing my application with nrf 52832 and nrf SDK v17.
I know NCS is more powerful. I'm currently learning how to use it.
But now.I still need my application with...
I'm writing a wav file from the nrf52840 board to the nor flash w25q128jv with a capacity of 16mb but it seems that I can only operate on the first 2mb, even when dividing...
Is there an AT command (For modem firmware >= 2.0.2) that can be used to validate whether the LTE modem can communicate with an external MIPI RFFE switch (for example on a...
Can Nordic share specific instructions on how to enable hardware tracing?
I've received the following patch from Tomasz, however I still see "trace clock missing" in Ozone...
Hi
our last product is based on nRF5340 and now we start a new design based on nRF54H20, and its essential for our design, i checked alot but there is no datasheet, reference...
just passed Cellular IoT Fundamentals while I was waiting for my nrf9151dk to be delivered... Now that I have the DK I can't get the dk to be provisioned...
I couldn't get...
NCS currently has a nice feature where the firmware versions are printed in the boot banner:
Is there a config option to also enable printing the nRF91 modem firmware...
Hi all:
I use the softdevice 2.0.0 and compile bootloader example with "dual bank" on the nrf52 DK,
Running a system that can using DFU from app then jump to bootloader...
Hi ,
I search and found some of questions on this forum wich speak about enabling and disabling peripheral.
I'm ok with that but i have a question about there initialisation...
I am testing the Nordic nrf51822 chip.
I have rewritten a bootloader example allowing firmware updates via Bluetooth LE (FOTA). A mobile phone will sent the update package...
Hi,
I'd like to transfer some data from my App (using fstorage) to the bootloader (using pstorage).
Given that that the two storage mechanisms are different, how can...
Hello, I've been working on porting a bit-banged control of a peripheral to use nRF51 SPI--which is just SPI rather than SPIM (therefore no DMA). Observe the SPICLK waveform...
Hi guys,
I am developing a project where I have a large group of NRF52 chips together in one room. In their normal state each chip is paired as a BLE peripheral device...
We are working on a NRF52 DK. In the data sheet of NRF52832, there is no mention of enhanced shock burst mode or dynamic payload or multiceiver. Do I need to refer additional...
we're using Mbed for NRF51822. our board using 2 GPIOs interrupt.
problem: the Rise edge did not generate the Interrupt event: set EVENTS_PORT.
I try uisng while, but...
Hello,
I will explain my setup:
I have 2 nRF51-DK each one of them connected via I2C and SPI to two different custom boards. One being the central(nrfA) and the other...
Setup: DK #1 is running native S110/SDK10/nRF51, one service 128-bit w/ 16-bit char:
Service UUID: 0x0xb1ad
Service UUID type: 0x0x2
Service handle: 0x0x0c
Service handle...
I found a discrepancy between a tutorial and an application note.
Step 2.A of "BLE Characteristics, a beginner's tutorial" devzone.nordicsemi.com/.../ calls sd_ble_uuid_vs_add...
Hi,
I tried to familiarise with eclipse environment and i have some problems :
The debug and run button. I searched on google but i didnt found anwser.
How can i define...
I find example : nRF51_SDK_7.0.0_2ab6a52\examples\properitary_rf\esb\esb_ptx_prx .
question 1: can i add this example into my project that build on SDK v610 and it run...
Hello,
I have an problem with DFU on nRF 52 I have followed this thread devzone.nordicsemi.com/.../ but failing to upload firmware.
I have attached screen shot. You...
