How can I display the nrf serial terminal logs files on VS Code while keeping the same colors and text highlights for dbg , inf , wrn , etc., just like when viewing live logs...
Hi,
I am trying to build bluetooth hci_uart sample for esp32 board and haven't had much success so far. I am running this command to build:
`west build -p always -b...
I'm using NCS SDK v3.0.2 and trying to build the Matter Thermostat example for the target: ` nrf54L15DK/nrf54L15/cpuapp/ns ` However, the build fails with the following errors...
when I try to build a code for integrating sensor in nRF 5340 dk, this error comes, I tried even after installing cmake manually from the cmake website https://cmake.org/...
Hello,
I am using an nRF9160 to connect to a private network. My nRF9160 successfully attaches to this network.
However, when reviewing the logs from the private network...
Hello,
How can I put the nRF54L15 into continuous wave mode? And I assume after entering CW that I can freely change channels using the FREQUENCY register (0x708). Is that...
Hi, I'm currently trying to add an Actinius Icarus IoT board as LTE device at nRF cloud.
I already know my board IMEI (I got it by flashing the AT client sample and then...
I want to use the MultiActivity Example with the nRF52 with GCC and Eclipse.
In the documentation I ve read that S130 and S132 are supported, but in the directory of the...
When I using the UART port, if I float the port after init the UART it will restart the code, is it need a external pull-up resistor? How about the value?
A quick one, where do I find a list of the err_codes? I have had a look in the documentation and I was expecting to find a table of them, but I couldn't locate one.
Thanks...
Hello!
I am trying to send a notification to a peer device when a certain event occurs. To do so, I'm using the same procedure as with every other characteristic with enabled...
I used the example of the ble_central\ble_app_uart_c and ble_peripheral\ble_app_uart.
It seems no problem for operation when I check only this example.
But I modified this...
Hello Everyone ,
I ahve deveoped the custom board using NRF51SOC and i have flashed the custom board by usign P20 Connector referred below figure now i would like to debug...
If I let the SoftDevice write to my variables directly by having the characteristics point to my app's variables through BLE_GATTS_VLOC_USER - when are these variables actually...
HI,i have some problems about RSSI (51882)
BELOW IS MY CODE. who can tell me why I can not get RSSI from variable t
int main(void)
{
uint8_t *p;
uint8_t t = 0;
...
Hi,
In S130, both central and peripheral modes are enabled. How do you enable just the peripheral mode and not the central mode for S130 so that less RAM space is used...
I am just working through the tutorial on radio notifications and imported "ble_radio_notifications.c" to my application folder and included the header in included directories...
I use NRF51822 Bluetooth 4.0 e-val kit.
souce code is peripheral example.
so, android smart phone and NRF51822 is connection.
result, Pairing success. occur On_ble_evt...
Is it possible to detect a bluetooth (BLE) enabled phone when it enters the room?
I like to use the nrf51822 (BLE-Peripheral or BLE-Central) to detect any phone when it...
Is it possible to have S110 but not more than ~30-40K size? I need to establish communication in order to upgrade firmware over BLE (UART Emulation), but without using such...
Hello,
Situation:
I am trying to write a characteristic to an iOS device acting as a peripheral from a nRF51822 board.
The board has 2 leds (green and red) and a button...
What is the file pstorage_platform.h? Is it an SDK file? Where does it come from? Is it auto-generated somewhere or should it be just copied from an example?
