Hello,
After I upload a new signed image to my device using MCUboot serial recovery (single image), MCUmgr Img_mgmt_client API
img_mgmt_client_state_read() always fails...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
Hi, i am learning with thingy 91 x and nrf9151dk. I made the online courses and succesfully conect to the cloud with the nrf desktop quick start in both devices. Now, i would...
Hello,
I am working with a custom board that has the nRF52840 (via the ISP1807-LR-RS module). This board has the SIT1552AI-JE-DCC-32.768E MEMS TCXO. This TCXO chip has a...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hi Experts,
I modified a DFU bootloader from SDK 9.0 for nrf51822_xxAA chip. However, I encounter code size overflow problem when building it.
I found the ROM1 configuration...
Here are my 2 scenarios:
I need a radio chip that will be used to form a mesh network in dense bush with each node up to 150m apart. Is this possible?
I need the...
Hi all,
Edit 25 Dec '15: Rewrote post for better readability:
I am trying to modify the dual bank DFU bootloader example to work on our custom board that uses a nRF51822QFAA...
Dears:
I try to use nRF52_SDK_0.9.0_0c82e3e SDK pheripheral pwm example and set the channel1(led2)
duty to 0.
But i still could get the signal about 400mv with LED2...
I've developed my BLE application that is based on nRF518822 and softdevice S110 v.8.0.0.
I've defined 6 services (4 with 2 characteritics each and 2 with 1 characteristic...
Hello,
I want to add uart debug support to the BLE DFU bootloader (nRF51822, S120, custom board).
Therefor I increased the possible size of the bootloader (start 0x39800...
Good evening and a happy new year to everybody.
Now it's time to work again, and I already stumbled about a little twouble while implementing a peripheral with concurrent...
Hey guys,
I'm designing an antenna for our open source sensor beacon, RuuviTag: http://ruuvi.com
Because we're using 1/4 wavelength monopole antenna, I'm considering...
for ble, scan of central device can get the RSSI value of the advertising device, but the inquire can not.
Is it right?
what's the different between them?
Hi,
I have made custom nrf 51822 board, I don't have LFCLK crystal i.e, 32.768khz. When i run ble_hrs example code in it , current consumption of my board goes to ~150uA...
Hi
In my application I need to transfer several paires of bytes to a slave device, and it's mandatory
for CS signal to go high between pairs. (This actually means I have...
Hi
I want to know why flash memory access should be scheduled in between the protocol radio event?
is there any relation between the flash access and radio opeartion physically...
Hello,
I am developing a wearable device that utilises nRF51822. Right now, I am having a problem because when the wearable device is connected to a new phone, it needs...
Dears,
I am designing a notification application. I would like to know what if I want to support both of iOS and Android phone, which example code of ble_app_alert_notification...
im following ( devzone.nordicsemi.com/.../) step to "Setting up a project for debugging in Eclipse"
i run the debug config and click suspend
then get some problems
...
