Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
I have a custom board with a nRF5340 and need to configure VREGH in DC-DC mode and set 3.0V output on it.
I see the documentation on REGULATORS — Regulator control where...
Hi,
NRF54L15, nordic sdk version 2.9.1
I recently lost ability to build my application. I get this linker error:
/home/adam/ncs/toolchains/b77d8c1312/opt/zephyr-sdk...
Hello,
Now, I currently run Asset_Tracker_Template on Thingy91X
https://github.com/nrfconnect/Asset-Tracker-Template/blob/main/docs/common/getting_started.md.
And, I...
Hi,
I have autoprovisioned and autoconfigured my nrf52840 board (provisioning and configuring are made inside the software and not through external app/provisioner).
In...
Hello Nordic Team,
Currently, we are performing power consumption testing using the Nordic nRF54L15-DK development kit.
As part of this, I aim to fully disable the Radio...
Hi,
I'm looking at interrupts from three different GPIO-pins. I'm setting it up like this:
static void gpiote_init(void)
{
uint32_t pins_low_to_high_mask = INTERRUPT_1...
Hi,
I'm using device manager for bonding starting from a sample application in the SDK.
I see that the DM_EVT_CONNECTION is raised before the BLE_GAP_EVT_CONNECTED but...
Is there a way to prevent nrfjprog from disabling target power from the J-Link when programming? I've tried setting power on perm but to no avail, nrfjprog powers down my...
I would like to know the RAM usage of my nRF51822 application. I found this post discussing some of it, but there is no obvious conclusion yet. I am using Keil for development...
I am using nRF51822-QFAA_Rev2. S110 7.1.0, SDK6.1.0.
First, program bootloader, then program \s6310\s110\ble_app_hrs\arm\ble_app_hrs_dfu code.
I use Android nRFtoolbox...
When performing a DFU using the latest iOS nRF Toolbox I keep getting an "Error on init Packet Message:Operation Failed". The DFU works fine with the same firmware application...
HI:
i use master control panel to write data to 51822(sdk8.0 ble_app_uart),but i can't write successfully.i do as help information.and i have selected the right UUID and...
I've just got up and running with the nRF51 DK. I've had a play with some of the examples, and now I've started on my own project using ble_app_template_s110_pca10028 as a...
After startup, I was able to send a spi msg from the master (app chip) to the slave(nordic). But when I try to sent the second message, I did not get any response from the...
I am using the SPI Slave peripheral and attempting to send the nrf51822 bytes from another MCU.
Am I right to assume that there is, basically, a 256 byte max per transaction...
Hi,
I have nRF51822 board which works great with my app when running on iOS 7
The application listens for iBeacon transmission and displays them.
When i installed my...
Hi, I made a custom PCB.
I use a Revision 2 MCU.
The antenna is printed. I didn't used the chip antenna.
Sorry for not showing both the full schematic and the...
Dear all,
I'm trying to connect the NRF51-DK (PCA10028) with a LSM330DLC accelerometer over TWI (I2C). I'm using the ble_app_uart example, included the twi_master.h file...
I need to implement a function to store some parameters such as uart baud rate and use these parameter for device initialization, The parameter could be modified when the...
Hello,
I`ve got a working S120 peripheral BLE device with custom services and characteristics.
I am able to connect and bond with iOS and Android. But I cannot connect...
