Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Description:
I am developing iOS app which will connect BLE and keep the connection till user don't want to disconnect. i.e we want to autoconnect BLE when BLE is in range...
Using Master Control Panel (MCP) with nRF51 Dongle PCA10000 v1.0
Segger is offering a J-Link firmware update - v6.10l:
Is this compatible with MCP? Is it safe to...
I am using RedBearLab Blend v1.0. I ran the HID_template and HID_keyboard_template. I can see the device in Win10 advertised as joystick and keyboard. Then I tried to modified...
Hello , i am going to use nrf51822 development kit ,but i am totally new for using it, i want to know that if i have development board and i want to see result but i dnt have...
Hello,
I need a little help regarding IoT-SDK 0.8.0 on nRF51.
In the MQTT-Example connection to the broker is established only when I press the button (callback), but...
Hi all,
I am facing issues when initializing and enabling the Softdevice after using the nrf_nvmc driver to erase and write flash pages. The project shall have the ability...
I am working with a MacBook Pro (El capitan) and the nRF51822 beacon and I need to measure the RSSI. I understand that the app nRF connect can do it, but the antenna on my...
Scenario is as follows:
NRF52 (SDK12.1, SD3.0) works in central and peripheral mode.
What happens is that on start we create a single shot timer with 4.2second to wait...
I write a function, It can read ok without BLE starting.
When I start the BLE , the function can not run.
So I think that , if I can use some function to stop the stop the...
Hi, all.
I tested ble_app_uart in example directory by PCA10040 board.
It works well.
printf ("UART Start!") in main.c works well. "UART Start" string cames out on putty...
Hello everybody,
I have a problem when I try initialize the ANCS service. The method ble_ancs_c_init(); from ble_ancs_c.h return the error NRF_ERROR_NO_MEM.
My configuration...
I flashed the nRF52 DK with the mbed bootloader developer.mbed.org/.../ but I'm having issues with the board. When I drag and drop the file which is a very basic blink program...
Hi,
I was trying to integrate a more simple version of the buttonless dfu example on my application. My first step was to get rid of the peer_manager and also the flash...
What is the use of of PCA10040 chip in NRF52 Development Kit(NRF52832 chipset). ?
Do I need a programmer to program NRF523832 in the DK, Can I just program it through USB...
Hello,
I asked a question after this old one : old one and I read other posts on the subject.
I wonder whether explained constraints may have changed or not since I am...
