Hi. I'm trying to write a simple MQTT app. I am consistently getting these KConfig errors to do with variables I'm not using, and I have tried to set CMake to ignore these...
Good day,
I've developed a board with a MDBT50Q on it. I'm using the Reg0 DC/DC and LDO Mode Disabled reference circuit ( https://www.raytac.com/download/index.php?index_id...
Hi,
I have the issue that my Zigbee device reports the error "Production configuration is not present or invalid (status: -1)". I followed the guide from this( https://docs...
Hi,
I am using an nRF52840 as a Zigbee NCP. I have built the firmware myself using nRF Connect, and I am also running MCUBoot. Sometimes after some usage, the chip starts...
Hello everyone,
I am testing out I2C on the nRF54L15 for a custom PCB project.
I first tested a simple mpu6050 sensor on &i2c21 on pins P1.11 for SCL and P1.12 for SDA...
I have a bit of an unusual use case where the nPM1300 is quite ideal but need to use an external charger for the battery instead of the internal charger. The nPM1300 fuel...
Hello,
We are currently developing with the nRF9151 and would like to request more information regarding GNSS SNR testing.
We have reviewed the documented GNSS functionality...
I am trying to use the nrf8002 for proximity type application. Right now I have a prototype working with a speaker and LED and I can light up either one using an app. What...
Hello every boby,
I'm a newbie in PIC programming and I hope something could help me to start interfacing the nRF8001 with a PIC. My schematic is already done but I don...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi
I'm using the Eval Kit PCA 10001 V2.1.0 and Nexus 5 with new Android version 4.4.2. Connecting to the Eval Kit works just fine, but when i perform a service discovery...
I have an nRF51822-based peripheral using the SoftDevice 110 v7.0.0 and SDK v6.0.0. The peripheral uses two custom characteristics under a single custom service. I'm using...
Hi
I'm using sd_app_evt_wait(); to go into low_power mode.
For some reason it comes back immediately, but I can't figure out why.
If I call it a second time it stays...
Hi,
I'm trying to flash the S110 onto my nrf51822 SoC, but nRFgo gives me the following error. (Also, hitting recover just gives me an error: "an error condition was detected...
Within app_button module, code for app_button_is_pushed() seems to have changed from SDK version 5.1 to 6.0. I notice my code has stopped working properly with that update...
Hi
Now, we are planning to implement an ANT+ RX (slave). I checked nRF51422 product spec. Radio current consumption is 12~13mA if receiving data between 250kbps and 2Mbps...
I'm using the boot loader that comes with the beacon development kit and I want to change it so that when the application software is running it can restart the device in...
I have managed to get the SPIS block working using standard sets of read and transmit buffers. This all works.
I am now trying to use the ORC register to send a single...
I am wondering how you put the nrf51822 chip to sleep. I've determined that the way to do this with the soft device is sd_app_event_wait() in the while loop. What about non...
Hello
I've been trying to create a simple BLE observer that outputs the nearby devices data onto the serial port using a PCA10001 board.
For this, I'm adapting the code...
Hi - I'm using the 51422 dfu bootloader from the nrf 6.0.0 SDK and it works fine with the iOS apps, I can send both .bin and .hex files to the device and it works fine. However...
Hi,
I am using nRF51822 evaluation kit. I want to develop GPIO isr (GPIOTE_IRQHandler) which can handle multiple GPIO interrupts. I have tried to enable the GPIOTE_IRQHandler...
