Hi,
I recently updated Nordic connect SDK and toolchain from v2.7.0 to v3.0.1. When compiling my application with activated CONFIG_BT_LL_SOFTDEVICE flag, I get this error...
Hello Team,
I am currently working with the nRF52832 and using the nRF Connect SDK ( NCS) with toolchain version 2.9.1. I would like to interface the nRF21540 RF Front-...
I don't have found CONFIG_OPENTHREAD_FTD feature in the bulb project prj.conf or prj_release.conf file, but I have found that it is enabled in the final .config file within...
I have installed nRf Connect for Desctop v5.1.0 on my windows 11 system.
I tried to update the Quick Start and install the Power Profiler.
Both gave me a similar error...
Hey All! I've been following the nRF Connect SDK Intermediate course from DevAcademy. In exercise 2 of lesson 9, bootloaders, you get to learn how to use KMU (Hardware Key...
Hi,
Testing Hardware: nrf52832 Module in a Custom board OR nrf52DK possbile -> We would like to change the order of the BLE service as shown in this thread: https://devzone...
Hello, I am trying to use the nrfx driver example to run an RGB led connected externally to the nrf5340 board. I dont see the led/pwm cycle running successfully. Can anyone...
My computer is running KEIL MDK4 and nRF51 SDK4.
So far no problem with nRF51422QFAAC0.
Upgrading to Keil MDK5 would be a nightmare, so that I gave up after a few days...
Hi,
I'm trying the nRF UART example but I can't get it to work.
I have opened the uart_example project in uVision and loaded it to PCA10001.
Then I opened the Master...
I want to add timer to send sensor movement data to PC every 8ms(125HZ).
But when I add app_timer like normal
1.raise APP_TIMER_MAX_TIMERS
2.raise APP_TIMER_OP_QUEUE_SIZE...
I am testing Keil MDK5 and created my own simple nRF51422 project (not from the sample), hello world type of code. But the "download" button is disabled.
The J-Link is configured...
Hi,
Can anyone please tell me the exact way to enter into the bootloader mode by writing some characteristics with specific value.
I tried setting
NRF_POWER->GPREGRET...
The existing Master Control Panel cannot be used as an automatic test platform.
Basically I am looking to send commands via a tcp/ip which will invoke scan/connect/disconnect...
I'm trying to measure a scaled down battery voltage level on an ADC pin. Given my resistor values the voltage on the pin should be about 0.279 times VBATT, to fit within 1...
Hi Nordic guys,
How much is the current consumption of the LDO only (quiescent current), without DC / DC converter, in uA? How much is dropout voltage and PSRR (ripple...
I try to modify "ble_app_ibeacon" sample code. But when I add some adv_uuids for services to advdata.uuids_complete or I changed advdata.name_type from BLE_ADVDATA_NO_NAME...
Hi,
I need to write a validation document for nRF51822 . The first step need is the specification for its calibration. But I couldn't find it in your website. Can you send...
Hello,
My project name is Remote Operated Vehicle. Basically i am using a PS2 controller as the joystick to control the car. So, my aim is to build wireless interface between...
In this function in nrf_gpio.h, why is there a GPIO_PIN_CNF_INPUT_Connect value there?
Shouldn't that be GPIO_PIN_CNF_INPUT_Disconnect, or does it not really matter?
...
I need to pass a bit, to 500 recipients in a closed room.
My doubt is, 500 receptors works simultaneously without interference?
Ref. to buy:
www.ebay.com/.../251458486443...
