I was doing development on the development kit and I noticed that when flashing the device there is application core and modem core firmware that is flashed
I'm trying to...
Background
Our device uses the CONFIG_LTE_NETWORK_TIMEOUT option from LTE Link Control, which by default is set to 600 seconds (10 minutes). I haven’t found any specific...
Hello, as the title suggests, I have an issue when powering the nRF9151 DK with an external power supply. Normally, I power through USB, and it's fine. However, when I followed...
Hi all,
I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
Hello,
We are working on Zephyr sample app Mesh on nRF52840dongle with nRF Mesh application.
After going through the documentation and few other Q&A on the portal, I was...
Hlo
I have designed a custom board based on nRF5340. Now I am trying to do flashing and RF testing of it through nRF5340 development board but can't even flash it because...
Hi all,
I'm encountering an issue with the TWIM30 interface on the nRF54L15 (pins P0.03 - SDA, and P0.04 - SCL), using vanilla Zephyr v4.2.0-rc1.
The setup involves external...
Hi,
I have a NRF52DK (Chip Label: PCA10040; V0.9.0; 2015.44; 682646724) and when i try to start the DK as described in the getting startet page, Step 5 failed as LED1 is...
Hi,
I am planning to make a program so that when a beacon goes far away a specific distance (around 5m) then the led should light up.
I have taken some measurements...
Hi,
I have a couple of eval boards that were created for software and hardware development. We have two versions of the nRF52832 on these development boards. I know that...
I am using nrf51822 powered by a 3.3V regulator in a li-ion powered application. We have a high current load that we're controlling with PWM at 20kHz. Radio performance is...
I want to bond with an peripheral, which has static passkey hardcoded in it. If I want to bond with it with MCP, I get an request for passkey, I can then bond and encrypt...
My environment for this is
Ubuntu 14.04
ecipse Mars2
ble_app_uart project of Nordic SDK11(makefile project)
armgcc
nRF52 PCA10040 Nordic board
ERROR...
I am trying to figure out how to exit a loop of my program using a button press on the nRF Toolbox UART app. Say it's button 4 for sake of giving it a value. I am using an...
Hello,
I've been trying to use nRF Connect 1.0.0 on OSX 10.11.6 with a nRF51822-powered board ( this one, to be precise ). Whilst nRF Connect finds the serial port and...
Hi,
I'm complete nordic newbie and asking you for some help.
I have 2x 81522 ICs, one is QFAAC0 and the other one is QFAAH1, both QFN48 packaged.
(1) looking at infocenter...
Hello I'm trying to learn your API using nrf5-ble-tutorial-advertising example. Over all the example is much help and API documentation is quite good. But part of API code...
Hi,
I am trying to do a GPIO operation every one second repeated in 51822. I am using app timer to get this work done. The current average consumption is 45uA/H. The handler...
The blinky_freertos example in the nRF5 SDK 11.0.0, built for the nRF52 (PCA10040) with GCC, appears to work fine right out of the box. However, when I added -DDEBUG_NRF to...
Hi,
Is it possible to communicate directly between nrf51dk(peripheral) and PC(master)?
With UART communication, I need to connect a board to the PC via USB. But I want...
We are using the nrf51822 with softdevice 7.0.0 and BLE.
We have noticed cases where sd_temp_get never returns and the processor resets due to watchdog timeout.
Under...
Hi Sirs,
I have 2 modules in Mass Production by using nRF51822QFAA & nRF52832QFAA.
Customer asking us to support Apple Home Kit.
Can get your advise for :
How to...
