Hi everyone,
Could someone help me with the following use case?
Task description: I'm working on a firmware update procedure based on the smp_svr project. I'm trying to...
Hello,
I have made a project that was based on the nRF9151 Development Kit and it works great. I had to select the -ns configuration to get anything to ever build and now...
Hi,
I bought a new nrf52840 DK board as one ofthe original nrf board of my Qorvo QM33120WDK1 kit ( 2 x nrf52840 DK + QM33120W + QM33110W) J3 connector broke. Out of the...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
I am trying to set up UART communication between the nRF9160 and nRF52840 that are found in the Fanstel BLG840XE. Currently I am sending a test string of "abcd" from the nRF52840...
Hello! This is the third time I'm asking something about the same project, but I'm running into problems one after the other.
The current problem is this - the hogp object...
I am attempting to update the firmware on a DFU V1 device using javascript inside of a cordova app. Due to the time it takes to roundtrip the write response it is going to...
Hello again,
Edit:
I am now only getting these 4 errors after enabling the clock in the nrf_drv_config.h file
I may be able to track down the problem myself if someone...
Hi,
I'm trying to get NFC working on a PCA10040 dev board. Using the nfc/record_url hex file it works fine, so the hardware is obviously ok.
However, when I use the...
I need to save data to flash on an nRF51422. I already have same basic thing working on an nRF52, so I figured the same API calls would work, but they don't. My main symptom...
I have an application that bonds to mobile devices and encrypts the connection on both Android and iOS. What I am noticing though, is that after each time I use the DFU to...
I want to stop advertising for 8 hours
but when I use
sd_ble_gap_adv_stop();
sd_ble_gap_connect_cancel();
It starts advertising after 1 or 2 secends again.
I think...
Hi,
I followed the tutorials shown below:
infocenter.nordicsemi.com/index.jsp
I downloaded SDK v11.0 and loaded S130 SoftDevice on my nRF51 DK. I use Keil uVision 5...
I am working on a bootloader for a client. I’ve been looking at the DFU example that Nordic has. The BLE version of the DFU needs to have the special format using the “nrfutil...
hi:
I use bootloader example of sdk 9.0.0 ,most cases worked fine, but I got gatt error sometime when I begin DFU. I had changed the dual_bank_ble_s110 into sigle_bank_ble_s110...
The nRF51 reference manual says that GPIO PIN_CNF registers are retained registers and that "a retained register is a register that will retain its value in system OFF mode...
Hi,
I'm trying to add second service on the fly, while SD running. After adding it, I'm trying to send service changed notification, but it don't work. Below is code used...
Hello.
I test nrf51822 central and peripheral.
I want to change radio channel frequency about nrf51822.
I test source code as below.
nRF51_SDK_10.0.0_dc26b5e\examples...
there is an error on softdevice on src\ll_adv.c on line of 659 . what is the reason?
this is my adv init
#define DEVICE_NAME "navid" /**< Name of device. Will be included...
hi
I want to know whether we require MCU for enabling "Enhanced shock burst mode " or when we set the CE pin to high for making RX that time automatically this will enable...