I have a ready hogp struct and I'm trying to subscribe to an input notification (I'm connecting to a bluetooth keyboard) and I'm getting error -22. Here's the callback in...
Hello,
I am trying to count pulses on nRF52840 DK's pin for measuring water flow with hall effect sensor. I tried to implement PPI + GPIOTE + TIMER in counter mode, but...
Hi, I am using nrf52840-based custom hardware and have an external flash connected on SPIM3. Till now I was working with my other peripheral connected on different buses and...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
Hello,
We are currently evaluating a very low power application using the nRF5340+7002. Our hardware design includes a complex power supply configuration, and we need to...
Retrieving Custom Firmware Version from nRF52 BLE Controller to nRF9160 Host
Product: nRF Connect SDK v2.6.0 Hardware: nRF9160 (Host) connected via UART to nRF52832 (Controller...
Hello,
I use EV-board PCA10040 and run I2C demo on path nRF5_SDK_11.0.0_89a8197\examples\peripheral\twi_sensor\pca10040. I measured the current over 5.7mA .if modifing the...
Hi.
I've got little problem with the uart connection to one peripheral. It's a normal 2-line connection without HW flow control. I'm using app_uart_fifo. HW is nRF52 with...
Hello,
i have a problem with the PCA10040. I try to set up a ANT Transmit Channel.
If "ant_channel_init" is called from main everything works fine.
But if it's called...
Hello,
I am developing in NRF52 with SDK v11. Initially I want to use CMSIS DSP library for statistic and FFT functions. However, I read that CMSIS Pack is not supported...
Hi,
I wrote a functional firmware which has been tested and valited on a nrf51822 QFAA, but unfortunately I need more RAM to fit the requirements of my application so I...
In the Android version of the Master Control Panel I'm sure that earlier versions of it hid the 'Connect' button for non-connectable devices. It seems they all have it now...
I'm starting to get things moved over to Peer Manager in SDK11 and when I call pm_conn_secure I get NRF_ERROR_NO_MEM. When reading the manual it states that this error means...
I'm using sdk10, I tried the bonding feature using device_manager and it's working. but then when I perform DFU, the bonding information is erased. I can't modify the bootlader...
There's a note in the migration guide which says .. very ominously ...
Applications must not modify the SEVONPEND flag in the SCR register when running in priority level...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
Dear Sir
In nRF51822 xxAA (Ram is 16kB),
softdevice(s120) is using RAM (address: 0x2000_0000 ~ RAM_R1_BASE).
I think that SoftdDevice region is used, after sd_softdevice_enable...
Hello,
It just a diode drop away from 3.9 to 4.2, and 20% typical of a Lipo discharge, just wondering whether the IC design and process is really that tight. The nRF52...
I recently tried to add security features (encryption, no MITM) to my application, and I am using nRF Sniffer to verify. nRF Master Control Panel gives me the request for...
Hi,
I'm newbie in the RF Design. For my project nRF52832 chip is being used for BLE and NFC. Have a query regarding the NFC section which is listed below-
Please refer...
