Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Can the nRF51X22 be paired with an iPhone to communicate (both ways) using regular BLE and emit a beacon signal at the same time? In fact, I'm looking to change the beacon...
So I suspect there is a very simple answer to this, but a couple days of much reading and searching haven't led me to a very clear answer.
My setup: Galaxy S3 (Android...
I'm trying to move data over the uart characteristic. I followed the guidelines here devzone.nordicsemi.com/.../
In the main loop I am calling sd_ble_gatts_hvx until it...
I'm working with an nrf51822 with the s110 softdevice. So I'm trying to read an analog signal from multiple pins. My program will run fine for quite some time. Eventually...
Hey guys,
I need to record many time interval ?, can i generate system time and use it to record all of my time intervals?
If I want to send all of the time intervals...
The gcc compiler is gcc-arm-none-eabi-4_9-2015q2.
The make version is GNU Make 4.0 (Build for arm-unknown-linux-gnueabihf).
The error message is:
... arm-none-eabi...
So I'm using the spi_master.c from SDK 6.1 to communicate with an LCD driver. I'm using an nrf51822 with s110 softdevice. My system has been sporadically hardfaulting on me...
Hello all,
I have found closed topics here with similar names ( devzone.nordicsemi.com/.../ etc.) but my question is about adding the characteristic with encryption.
My...
Hi,
I'm trying to transition my application from SDK 7.2.0 to SDK_9.0.0 and am having some issues when including ble_advdata.h compiling with gcc:
In file included from...
Hello,
I know I'm not supposed to use TIMER1 with IRQ 0 when using a SoftDevice but I want to try anyway :) I want to do some bit banging with timing that is timing sensitive...
I am trying to program custom boards with the NRF51822 using an ARM-Flasher with no success. Using J-Flash I can connect to the device properly, program and verify the hex...
What could be the reason for?
Couldn't find any error descriptions.
Using Laird BL620US with newest FW v12.4.14
Error occurs as a response to 'scan start 1000 0 0'...
According to the *.map file the .bss (RAM) usage for my Application is 0x16b8 or 5816 bytes. This is obviously a very high RAM Application, likely due to the abundance of...
Hello Nordic,
I am working on [nrf51822 custom board+SDK8.0.0+SD110]. I need to test button press bouncing and de-bouncing, how it works on the board ? I found one example...
Hi,
is it possible to use this module from LAIRD in connection to the nordic SDK - i installed the softdevice hex but the hrs example for s110 is not running properly ...
