I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
Hi all,
I'm trying to use the experimental ANCS example with an iPhone iOS 8.3. My Nordic SDK is 8.0.
The sequence is the following :
Flash the example on the dev...
Hi,
I'm looking at interrupts from three different GPIO-pins. I'm setting it up like this:
static void gpiote_init(void)
{
uint32_t pins_low_to_high_mask = INTERRUPT_1...
Hi,
I'm using device manager for bonding starting from a sample application in the SDK.
I see that the DM_EVT_CONNECTION is raised before the BLE_GAP_EVT_CONNECTED but...
Is there a way to prevent nrfjprog from disabling target power from the J-Link when programming? I've tried setting power on perm but to no avail, nrfjprog powers down my...
I would like to know the RAM usage of my nRF51822 application. I found this post discussing some of it, but there is no obvious conclusion yet. I am using Keil for development...
I am using nRF51822-QFAA_Rev2. S110 7.1.0, SDK6.1.0.
First, program bootloader, then program \s6310\s110\ble_app_hrs\arm\ble_app_hrs_dfu code.
I use Android nRFtoolbox...
When performing a DFU using the latest iOS nRF Toolbox I keep getting an "Error on init Packet Message:Operation Failed". The DFU works fine with the same firmware application...
HI:
i use master control panel to write data to 51822(sdk8.0 ble_app_uart),but i can't write successfully.i do as help information.and i have selected the right UUID and...
I've just got up and running with the nRF51 DK. I've had a play with some of the examples, and now I've started on my own project using ble_app_template_s110_pca10028 as a...
After startup, I was able to send a spi msg from the master (app chip) to the slave(nordic). But when I try to sent the second message, I did not get any response from the...
I am using the SPI Slave peripheral and attempting to send the nrf51822 bytes from another MCU.
Am I right to assume that there is, basically, a 256 byte max per transaction...
Hi,
I have nRF51822 board which works great with my app when running on iOS 7
The application listens for iBeacon transmission and displays them.
When i installed my...
Hi, I made a custom PCB.
I use a Revision 2 MCU.
The antenna is printed. I didn't used the chip antenna.
Sorry for not showing both the full schematic and the...
Dear all,
I'm trying to connect the NRF51-DK (PCA10028) with a LSM330DLC accelerometer over TWI (I2C). I'm using the ble_app_uart example, included the twi_master.h file...
I need to implement a function to store some parameters such as uart baud rate and use these parameter for device initialization, The parameter could be modified when the...
