Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
I want to make rs485 communication with nRF51822. I gone through the UART code, there CTS , RTS pin are required , but for my case tx, rx,rx enable is enough, and also shall...
Hi everybody!!!
I am making a project which use NUS service and I have confuses in connection mode:
when the central and peripheral do not have data to transfer...
Hello, my question is pretty clear i guess. Is it possible to schedule advertising of 2 different packets on the same chip ?
The way i see it, it should be possible to...
Good morning, I´m trying the example of this post (ble_app_template_with_pstorage_operations_nRF51DK.zip). I have SDK 8.1.0, softdevice 110 and nrf51-dk.
The source works...
Is there any clear documentation to add an external memory to the nrf51822 to store some sensor data. How is the performance and stability when interfaced this way?
Dear all,
I'm working with nrf52832 and SDK 11.0.0.0.
I want to upload SD 2.0.0-7. Download results OK but,
nRFgo Studio, when accessing the unit reports:
Region 0...
I just got the signed bootloader to work with the single bank implementation but had to change dfu_single_bank.c. I believe the change represents a bug in the code.
In...
We are working on a nRF51 device and and corresponding iOS App, and we would like to set the name of the device. The problem is that when connecting with an iPad using BLE...
Hi,
Im trying to use BLE DFU Bootloader from examples. I loaded SD8 and then bootloader via nrfStudio (dont have a valid app flashed), but I cant see the device from Android...
In [sdk10_folder]\components\ble\ble_db_discovery.h , BLE_DB_DISCOVERY_MAX_SRV is given the value 2 .
In [sdk10_folder]\components\ble\common\ble_gatt_db.h , BLE_GATT_DB_MAX_CHARS...
In another thread entitled:
Change in GPIO to start/stop timer and fire interrupt
The following code is used:
NRF_GPIOTE->CONFIG[0] = (GPIOTE_CONFIG_POLARITY_HiToLo...
Hello,
I'm trying a very simple thing; to light a LED on button press. I'm using SDK 9.0.0, nRF51 and SoftDevice 110. However, button handler is not firing.
So, APP_BUTTON_INIT...
I'm new to using nordic parts (nRF52832). We were previously using device manager/pstorage but recently transitioned to peer manager/fstorage.
However, we presently manage...
