I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I've created a custom service for a demonstration. I can view the see the device in Master Control Panel and view notifications and write to a characteristic that is writeable...
Hello,
I have a question about RAM usage. If i use chip with 16kB RAM, and if i use s130 (which uses 10kB RAM) and bootloader (which uses 4kB of ram) i only get left with...
hi, i am getting start nrf 51822 BEL with ble_app_uart
as a first step, i just compile the one of the BLE example 'ble_app_urat" which is located in 'C:\Keil_v5\ARM\Device...
I have a project that uses the nRF51822_xxAA chip with a pull-up button connected to pin 9. Using a meter, I have verified that the pin drops low (0 V) when the button is...
Hi,
I'm reading temperature and humidity from 2 sensors in my system
At some point in time during a quick and dirt check the system has been proven working fine and...
HI:
everyone!
How to make the matching and binding equipment information would be stored permanently, even after the OTA upgrade is still in;I made with examples of the...
Greetings, I tried to modify the parameter "len" to anything over 1 (byte), but it just doesn't work.
As long as it's over 1 byte, the API crashes my program. err_code shown...
Hi,
I'm using s130 as softdevice for nrf51822. I program the softdevice with the official s130 hex file. According to the hex file, there is no data at address from 0x7c0...
We're working on an application that needs ultra-short range BLE, on the order of 50cm radius or less. I've found little discussion anywhere on that topic, likely because...
I notice that the dongle has a 3.6V-5.5V input and a pin that sais 3.3V, I measured 3.3V on this pin so I was curious if I could run an IMU unit and an i2c/spi bridge requiring...
Hii all
I am trying to port the experimental/bootloader_signing project to gcc I made changes in the project accordingly, so now its working. I can able to flash application...
I connect a GPS module to nRF52 DK and connect nRF52 DK to my computer once more.
GPS module ---> nRF52 DK ---> computer. (like this)
So I want to do NMEA parsing like...
Dear All,
I am sorry but I have to ask this question here, I searched and red trough the forum, tried the suggestions, nothing works.
Basically I want to have a HID device...
I use softdevice 6.00, size is 80K Byte. I use the chip NRF51822ab,and configurat the irom start at 0x14000,size 0xC000, IRAM, start at 0x20002000,size is 0x2000 ,in keil...
Hi,
Is there a possibility to read the state of the gpiote pin? (is it high or low). Is there any function or any other way to do that?
I'm changing the gpiote pin via...
