Hi
our last product is based on nRF5340 and now we start a new design based on nRF54H20, and its essential for our design, i checked alot but there is no datasheet, reference...
just passed Cellular IoT Fundamentals while I was waiting for my nrf9151dk to be delivered... Now that I have the DK I can't get the dk to be provisioned...
I couldn't get...
NCS currently has a nice feature where the firmware versions are printed in the boot banner:
Is there a config option to also enable printing the nRF91 modem firmware...
Dear all,
after cutting the SB bridge to the QSPI chip and close the ones to get the pin free and disabled also qspi inside the nRF52840dk_nrf52840.overlay file I'm unable...
Hey, I have a problem understanding BLE behavior
I had a product was running in BLE phy 1M, and I wanted to convert it into PHY CODED.
It just sniffs all the advertisement...
Dear all,
I stubled upon the following issue when developing a BLE sensor product. When I try to bt_gatt_notify(); With only one characteristic, there is not an issue...
I was looking into the sdk provided by nordic for nrd52840Dk board and want to test the zigbee protocol. I havn't find any sdk for that.
Can you share me some links and...
Hi everyone
I'm trying to implement the MQTT sample on my devkit but I'm a little bit lost. I never used the MQTT before, so its a little bit of a chocking to me.
From...
Hello Nordic team,
I am using SAADC in order to read values coming out of my current sense amplifier [INA180]. I am sensing the current through a fan which takes up to...
Hi,
I am trying to verify current consumption of nrf52840 DK (not any peripheral connected ) before doing that for our product.
We need to use RTC to wake up the device...
Hello,
I need some help updating NRF52840. This is my first project and I have a working application which uses Softdevice 140. I would like to update it with usb-serial...
hi all ,
zephyr bt_hci_core: HCI driver open failed (-5)
i follow this link .(open lte-m(udp) and gps between psm mode on NRF9160)
now ,i need add HCI driver to control...
Hello,
I am working on nRF52832 using SDK 15.3.0 in segger studio.
In my application I am calculate time interval of plus, In which i am given plus to the board pin...
I use:
pca10059, connectivity_4.1.1_usb_with_s140_6.1.1.hex
nrf-ble-driver-4.1.1-win_x86_32
I am trying to scan BLE advertise. I have a problem that ALL packets...
Hello,
I am using Segger and nrf52840 dk. I want to print float value in debug terminal but the value is not getting printed.
I did this-- printf("%f cm\n", temp);
in...
Hi!
I am currently trying to build the lwm2m_client. Currently I am using ncs v1.1.0-rc3.
I am using the devkit as hardware. The only thing I changed in the proj.conf...
Hi Nordic Support Team,
i'm working with nrf52832 development kit. In that, We are adding the UART features in BLE DFU secure bootloader example code in SDKV15.2.0. But...
Hi all,
I have tried to write a program for configuring and send a character data over UART,but the NRF52-DK not responding to the code,I successfully flash the code.
...
I can't seem to get TWI working, attached are main.c sd_config.h
The code compiles, but when stepping through in debug, it ends up in an infinite loop inside:
I have...
Hello,
I am in the process of integrating a project where I need 3 uarts to work concurrently in different configurations. This will eventually migrate to an application...
Sorry ,I have the problem with increasing the max data length(more then 20 bytes) in the characteristic , I change the att_mtu size like the value in the picture, but after...
