Hi everyone,
I'm working on a project using the nRF54L05 (v2.9.0) and I'm currently facing an issue with BLE. I want to change the BLE transmit power , and so far I’ve only...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi,
I’m trying to understand the following parameters in the nRF54L15 channel sounding configuration, because their function is not clear to me. I added my questions as...
We encountered some problems while debugging the nRF54L15. A total of 10 circuit boards were produced, and the chip on the board is nRF54L15CAAA. After programing the code...
Issue:
I would like to bring to your attention that I am getting an error when running the 'list command using the nrfcredstore cli utility, while trying to retrieve the...
Are there any migration guides for a customer who wants to migrate from nRF5340 to nRF54L15? And if they are nRF54L15 in chipscale, anything they should be aware of including...
Hi,
I am facing an issue with the nordic 51822. I am declaring a gpio as output. I am writing logic High to that pin. When I check the signal in logic analyzer and multimeter...
Using rev 0218 firmware I am getting an awful lot of device errors with the mbed kit. I am not sure if this is a Nordic or an mbed issue so am asking in both places. Symptoms...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
I'm testing SPIM of nRF52 on PCA10040 using S132 and SDK11.
Its base on the app_peripheral_uart example, so I already have BLE communication.
When SPI is not initiated...
I have just received a nRF52 DK board and I am as a start trying to compile the associated Blink program in Keil 5.18 Lite. When I copy the blink example using the Pack Installer...
hi,
I was reading documentation and forum but failed to get a clear picture how AES module work.
So far my understanding is:
There are two ways to access AES either...
I'm building a product that can use the features from your Smart Remote 3. Is there someway to get the reference source files so I can adapt some of the smart remote features...
Hi,
Few days ago I received my DK-52, I set up the development environment based on Keil and started to compile some of the examples included into the SDK. I have not a Windows...
I have been googleing for a solution but have not found any solution yet.
Have tried the following:
Installed J-Link commander. (Does not pick up any usb devices...
We are a newbie team developing some measurement tests with the nRF52832 DK in order to evaluate the BLE from nRF52832 QFAA80 (s132 and pca10040) for IoT applications.
...
hi all,
Question:
i want to print "BUTTON IS PRESSED" continuously when button is pressed and i want to print "BUTTON IS RELEASED" when button is released.
eg: if i...
Now，I use a 1s timer to calculate the clock.
At first,I use the telephone to adjust the time to fit the telephone time.
but finally(after a night ) the result runs fastly...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
I'm trying to get a UART example running on the nRF51822 mbed kit. However, flashing any uart examples from the SDK onto the board generates a fail.txt file
What is the...
