Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Even I am writing BLE applications, but I don't totally understand these items:
In Characteristic Properties of GATT Characteristic metadata
We have read, write, notify...
I am trying to trigger some functions based on some pre-determined timings. I tried to do that using nrf_delay_us and also using timer0 interrupts, but both are giving me...
Hi,
I'm using nRF Master Control Panel to test a Phone Alert Profile (PASP) I've implemented. For this, in the app I configured a GATT server that exposes the Phone Alert...
Hi,
I am using nRF5_SDK_11.0.0 to learn how to use BLE stack to communicate.
For the BLE HRS app, I want to achieve sth. like this:
Central node can configure the sending...
Hi,
I'm not sure if this forum support that board but if YES, can You explain how to upload some program on that board. I think that process is little bit different that...
For some of the examples i see different versions
For example the ble_app_hts example
It has a _hci, _spi and a _uart version
In the documentation i don't find any info...
hello everyone！
I have just contact nrf51822, the agreement with the application framework is not very familiar with, you can share a quick start of the information, the...
Hi everyone,
Where I can read transmission type and device number of connected ANT+ device (HRM)? I want save those values and bound later only with currently connected...
I tried to set a custom key in this way:
... ANT INIT
uint8_t network_number = 2;
uint8_t p_network_key[8] = {0xa1, 0x15, 0xb3, 0x66, 0x60, 0xef, 0x19, 0xa1};
err_code...
Hi there.
I'm woking with sensor in board nRF51822.
Do we have any tool to test oscilloscope i2c?
I want to check the signal is same as what I sent or not.
Thanks...
Since nRF51 is multi-protocol, why don't Nordic provide support for Zigbee? This way, customers can simply buy one single chip and have several standards supported. Are there...
I received a NRF_ERROR_INTERNAL error from a pstorage_store() function. As far as I can tell this error should not result from this function. It occurs fairly randomly. This...
In the examples delivered by Nordic, there is ble_app_hrs in ble_peripheral and ble_app_hrs_c in ble_central. But I cannot find a ble_app_hts_c in ble_central for the ble_perifpheral...
