I'm writing a wav file from the nrf52840 board to the nor flash w25q128jv with a capacity of 16mb but it seems that I can only operate on the first 2mb, even when dividing...
Is there an AT command (For modem firmware >= 2.0.2) that can be used to validate whether the LTE modem can communicate with an external MIPI RFFE switch (for example on a...
Can Nordic share specific instructions on how to enable hardware tracing?
I've received the following patch from Tomasz, however I still see "trace clock missing" in Ozone...
Hi
our last product is based on nRF5340 and now we start a new design based on nRF54H20, and its essential for our design, i checked alot but there is no datasheet, reference...
just passed Cellular IoT Fundamentals while I was waiting for my nrf9151dk to be delivered... Now that I have the DK I can't get the dk to be provisioned...
I couldn't get...
NCS currently has a nice feature where the firmware versions are printed in the boot banner:
Is there a config option to also enable printing the nRF91 modem firmware...
Dear all,
after cutting the SB bridge to the QSPI chip and close the ones to get the pin free and disabled also qspi inside the nRF52840dk_nrf52840.overlay file I'm unable...
nrf51822bluetooth low energycode 10
twiddle gravatar image
twiddle
1
asked May 9 '16
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just...
Hello Everyone,
I am designing the prototype using NRF51822 and i have choosen the DC DC power mode but the real problem is most of the time my radio will be sleeping so...
I have nRF52 Development Kit (PCA10040). I'm using Keil uVision.
I want to measure RSSI of some beacons and if the signal is strong then send MAC of this beacon over UART...
Hello Everyone
I'm trying to debug ble_app_beacon project, having the following error when trying to launch the debug session:
Error in final launch sequence Error executing...
Dear Sir:
I have a (BLE + 2.4GHz)Mouse project, But now I had some problmes. Please help deal,
Thank you so much Sir.
a). My program modification base on "nrfready_desktop_2_v3...
Hello all,
Just to note any versions that need saying, I am using
SD 110, V8
The 10.0 SDK, freshly unzipped
The dual bank BLE bootloader, unmodified
Arm...
I was looking at this PA/LNA example: here . I noticed something I'm not sure about, so I was hoping someone could shed some light on this.
In the diagram shown in the...
I've been working on a project, which requires data transmitted through ble to cell phone app. The user could acquire the data from the sensor when he sends a specific string...
Hi
We use the NRF51 in a mesh sensor network. We noticed in a trailer suited for cold chain transport (double metal walls with thermal isolation between) that the radio...
Hi,
I have problem with ble_nus_c.c in SDK v11...
Normal operation is:
Connecting to target 57E19A190FDF
Connected to target
[DB]: Starting discovery of service...
When I used the demo of ble_app_hrs_rscs_relay,I cannot write the bonding information to the flash.
I connect to the board by my phone.I cannot find the information about...
what I am basically trying to do is only allow a single bond and any new bonds disallowed until the user selects and option to allow a new bond and then and only then delete...
If I have 10 slaves and one master in a bluetooth low energy network, and the connection interval for all 10 slaves are set to 7.5ms, how would the master manage this?
...
I intend to use RC oscillator instead of external crystal oscillator .
I modified code :
from
SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, NULL);
to
SOFTDEVICE_HANDLER_INIT...
Hi,
I want to identify different kinds of center in a device product. So I have 2 questiones:
1) Can a center (running S120) set its own name?
2) Can a device (running...
