Dear reader,
I am currently working on a project using the NRF54L15 MCU. There is plenty of documentation available for this component, and the reference circuitry for the...
I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
Hi everyone,
I'm working with the nRF9160 and trying to configure P0.19 as the UART TX pin using Zephyr. Here's the configuration I used in the device tree:
uart1_default...
I have shifted from silicon labs for BLE project. In Si labs we have burn BLE bootloader and BLE application separately. Do i need to do the same here in nrf controller? If...
Hello,
I am using nRF Connect SDK v3.0.1, together with the Find My add-on. Test case TCG013 of the Find My Network Self-Certification Test Cases R1.7 is failing on the...
I am unable to detect any i2c device when connected to the Nordic nRF54L15 DK kit. I have change the voltage from 1.8v to 3.3v and Tried and explore other pins in Port 0 and...
HI: D:\ncs\v3.0.0\nrf\samples\bluetooth\peripheral_uart Using the nrf54l15DK board can run peripheral_uart examples,connection is disconnected. However, when I use the nrf54l05...
Trying to follow
devzone.nordicsemi.com/.../
but whatever I do, I am unable to make Eclipse discover the include paths or the source file paths from the makefile. I've...
Hi,
My Nordic kit just stopped detecting from last two days.
I have also check this in other PC also.
It detects some times some times not.
I am using Windows 8.
I...
Hi all,
I would like to know if it is possible to use the uart before the actual bootloader runs... I need to communicate with the master uploading the firmware before...
Hi All,
I need to implement a kinda a mesh network of Nordic device nodes placed nearby to act as a relay, for that I have a use case where following requirement.
...
I'm porting a nrf51 project to nrf52. I'm using softdevice s132 1.0.0.3 alpha. When compiling I get a lot of L6406E errors and a L6407E error. Do you know what's causing this...
hi,
I should how to transplant the official DMP mpu6050 library to nrf51822 above?I don't know how to transplant it and could you tell me how to transplant it?
I have combined to programs Ble_uart and Spi_Master into one. However, after uploading the file the GPIOs do not work (No clock is generated). Meanwhile when I erase the softdevice...
hi,
I downloaded the master control panel(mastercontrolpanel.3.4.0.8098.x64) from Nordic website, but it can't install it in my PC becuse of my 32 bit windows XP system ...
Hi,
Here is the piece of code that is bugging me.
The code algo is at every 500ms timer2 interrupts, and the adc captures 1500 samples and stores it in an array .I always...
I'm using nRF 51822 to develop a proprietary wireless protocol.
At Rx side, every 500ms have a listening window with 10ms to listen if there is package to receive. So 10ms...
I am testing with SDK6.1 S110 7.1. I've noticed that when I try and update the Bootloader image using the Android MCP app, everything updates fine. I have logic in place that...
Hello fellow developers,
I am new to BLE applications and I am trying to do a very simple device with three buttons that informs a Android smartphone when one has been...
Hello all,
I have an ANT project which is running fine using S210 SoftDevice (SDK v8.1.0).
Now, I am trying to extend this project for BLE operation, by switching the...
I have my devices programmed in a way, that they decide whether to enable SD and transmit via BLE or to keep it disabled and start operating using Gazell.
In this case I...