Hi,
I’m using the function lte_lc_psm_param_set(rptau, rat) . After connecting to LTE, I call lte_lc_psm_get(&psm_cfg.tau, &psm_cfg.active_time) and receive the following...
Hi,
Developmente setup: Windows x64, nrf connect for vs code, SDK and toolchain versions 3.0.2.
I was trying to build a proyect for a custom nRF5340 board when I encountered...
Hi,
I am getting randomly incorrect SOC reported by pmic npm1300. For most days, it reports correct SOC but then all of a sudden it starts to report incorrect SOC even though...
Hi,
I recently found out about the Periodic interval feature on GRTC CC[0] and it seems like it would be quite useful for my application. Most of my code so far uses the...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
I'm trying to implement a fall detection feature on the headset side using the LSM6DSOX IMU sensor. The IMU is configured successfully, but the board halts after the INT1...
I have a ready hogp struct and I'm trying to subscribe to an input notification (I'm connecting to a bluetooth keyboard) and I'm getting error -22. Here's the callback in...
Hi everyone,
I'm facing an issue where MCUboot doesn't perform a swap after reboot, even though the DFU download to slot 1 completes successfully and boot_request_upgrade...
Hi
We are migrating from Segger Embedded Studio (SES) to VS Code for developing in the nordic connect SDK. We are using the RTT logger for debugging our device. In SES you...
Hi Nordic,
I test with nRF7002-DK and IC mark on nRF7002 is below:
N7002 QFAAB0 2252AA
Here is my test data, showing about a 3dB discrepancy between power setting...
We are currently using Zigbee Firmware built with nRF Connect SDK v2.7.0 on the nRF5340.
We plan to upgrade the nRF Connect SDK to v2.9.2 and use the Zigbee Firmware built...
When I was using the code from the following website, I encountered many errors while creating a new build for compilation。
https://github.com/NordicPlayground/nrf-esl-bluetooth...
Setup: - We have a custom board using the BL654 (Laird Connectivity) module with the NRF52840 core using SDK 17.1
Issue:
- On power up we configure the GPIO 41 as an input...
I am trying to compile hci_lpuart for thingy91_nrf52840, but I have these issue. hci_lpuart:
Any ideas on how to solve this? I'd really appreciate it. And if you have any...
Hello Nordic,
I am looking for a sample or instruction (step by step) for custom bootloader.
Our application code is ready and all the left thing is BLE DFU and custom...
Hi, I was using the BLE online power profiler to determine possible power savings with the nRF54L15DK over the nRF52840 using the zephyr bluetooth broadcaster sample. The...
Hi, I am using ncs 3.0.2 and an looking at adding extra .conf files during production. For the app it works fine using --extra-conf, but I can't figure out how to add one...
Hello DevZone team, I recently received a new nPM1300 Eval Kit (PCA10152, 1.3.0, 2025.19) and connected it the first time following the documentation ( docs.nordicsemi.com...
I have an NCS v2.6.1 project on the nRF52832 where I'm using both the zephyr timer APIs
and the nRFX TIMER drivers
This causes some perplexing issue where my Zephyr...
Hello,
We upgraded our project to nrf connect sdk v3.0.2 from v2.9.0 and can no longer use pin 0.00 and pin 0.01 as gpio. The problem seems to be in the nrf53 soc.c file...
Problem with exercise code in a developer academy fundamentals course.
Exercise:
Bluetooth LE Fundamentals Lesson 2 Exercise 3
SDK:
v2.9.1
Board Target:...
Hi,
I am programming with nrf52833,ncs v2.9.0,generating peripheral_uart to peripheral_hid_keyboard sdk.
And now with working serial times,err happend and log is Not able...
