Hello,
I'm trying to transfer data from peripheral to Central (based on Central Uart and Peripheral Uart samples) continuously with a delay between each packet of about...
Bluetooth do host connection peripherals occasionally appear 0x3E error, want to ask what may be the cause. In addition, when other scanning devices of the same type are also...
Hi
I am compiling GNSS sample project for positioning.
I am using nrf5340dk_nrf5340_cpuapp_ns development board. I want to use Quectel L86 with nrf5340 dk.
I am getting...
Hi,
I am using the nrf5340 to study the flow of BIS broadcast audio. I have two nrf5340s, one as gateway to run the broadcast_source program and one as headset to run the...
Hello,
I have (2) Questions below highligted in yellow
I have followed these steps until Step 5 Substep (1-4)
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest...
Hello, I am trying to connect to an MQTT server using PEM certs and mqtt helper, however I get an error: -22 from mqtt_helper: mqtt_connect I have traced the issue to zsock_connect...
Hello Nordic community,
I'm currently working on a project that involves BLE (Bluetooth Low Energy) using UART configuration alongside FRTOS (FreeRTOS) in a PCA10056 dk...
Hi All,
I need to interface with a Monolitic's MP2731 battery charger, it has an i2c interface, and want to create a custom in-tree driver for it.
My question is, Is there...
Hello everyone,
I am designing a custom board based on nRF52840-QIAA, so my question is:
The output radio impedance of the nrf52840 is not 50 ohm and now I want to calculate...
Hi All,
I am planning to use AWS fleet provisioning (by claim) with nRF7002 DK. I have seen the example with nRF9160DK but I have not seen any information for nRF7002DK...
Dear All,
I need to implement fully disabling and enabling several hardware components and drivers (UART, comparator, PWW, etc.) that I'll need only when the user asks for...
Getting undefined reference to `<already_defined_variable>'
So I was using SES v5.70a
Actually I was new for the developments using SES for Arm MCs
I picked up an...
Advertising ->Establishing first Connection-> Advertising again to allow another connection.
Should I keep a different BLE address for second advertisement?
Or just...
I have a development problem, please help me. Due to the power management requirements of the product, I need to enable and disable the ADC function in the program to save...
I am having a recurring problem with NFC-CONNECT: build action. It hangs when building. Gets stuck with the following message in lower-right hand corner of screen:
The...
I am testing peripheral UART sample code with nrf5340DK along with some other device. I have connected the UART pins of that device with nrf to receive its data.
I am continuously...
Hi there,
I use the ADC in my firmware, which works well, but I also want to use it from the shell.
I enabled the CONFIG_ADC_SHELL Kconfig option, which made the "adc...
Hi,
I have been using the nRF9160-DK sample code to connect my dk to my hosted Azure IoT Hub. I have followed the documentation for creating the certificates for both the...
Hi Nordic
Sample: asset_tracker_v2 (with only changes to overlay-azure.conf) SDK: 2.5.2 Modem FW: nrf9160_1.3.5
I have followed this tutorial https://learn.microsoft.com...
Hi,
We have a custom board that includes an ST LIS2DE12 sensor. I followed what looks like the normal procedure to create an out-of-tree driver for it by refactoring the...
We recently got the NRF9151-DK and were trting to measure the e-DRX current on the system working on CAT-M1 network. The NRF9151 DK is loaded with Serial LTE Modem application...