Hi,
TWIM does not work well with nRF5340DK as shown in the subject. The conditions are shown below. - I/O voltage is not 1.8V. The waveform is distorted around 2.5V, though...
Hello Team,
We would like to keep the necessary build configuration for a board in Bitbucket,which are necessary to show up the "Build" folder in VS code.So that every developer...
I am using NCS Connect SDK version 2.6.0
I am trying to create an array of models and found a problem with using Zephry macros in C++ projects. My main.cpp is as below ...
Hello community,
I am trying to develop a custom bluetooth HCI_USB code for the BL5340PA BLE controller board. The Liard Connectivity's(now Ezurio) BL5340PA : https://www...
Hi
I use nRF7002-DK, SDK:V2.5.2 with zephyr driver, I need to send recieved data or command from uart, data type is using with hex byte array to send, from example , the...
i need information on power consumption during advertising and connection in my case its taking too much high current around 1 ma in advertising and 1.5 ma during connection...
Hello support team,
I am a beginner in this environment and I am facing a problem while trying to compile my project in Zephyr for nRF52840dk board. I am trying to run this...
Hello
I have 2 devices ,a central and a peripheral on a custom nRF52840 board
Using Zephyr SDK 2.5.0
The distance between the devices is 10.9 meters. When TX power on...
Hi,
We have been using SDK version 2.1.1 and currently are in the process of migrating to SDK version 2.5.0.
Would be helpful to get some hint regarding what conditions...
Hi, I am developing on NRF5340 chip, using an external Flash memory (AT25SL321) on my custom board. I was previously using vanilla Zephyr version 3.1.0 (everything was working...
Trying to implement FOTA DFU over BLE. My application uses my proprietary code (instead of mcumgr) to download signed OTA firmware image to secondary slot (in my case it is...
Hello and thanks for reading.
I have a critical problem with my device, and seeing as the problem is BLE related I figured I would ask your help as well. We are using the...
I'm trying to enable DFU on our device but am getting a lot of issues.
I used Device Manager to upload app_update.bin and it worked. If I use Flutter example to upload firmware...
Hello,
I am developing matter sensor and I would like to send data to `MeasuredValue` attribute of `CarbonDioxideConcentrationMeasurement` cluster. I followed this tutorial...
Hi community,
ncs-2.6.0 I'm using.
I'm trying to enable bmi270 as I enabled adxl362(is already working), both are connected with SPI.
but it shows me this kind of...
I am trying to write and code of aes encryption and decryption using ccm mode for my application on nrf52832 controller. I have went through some example on Github for the...
I am working on an application with significant constraints on power consumption and distance immunity. After some research, I found the Thingy:53 module, which is well-suited...
Hi
I use nRF7002-DK, SDK:V2.5.2 with zephyr driver, I need to send recieved data or command from uart, data type is using with hex byte array to send, from example , the...
We had tried AT#XSLEEP=1 command in nRF SDK 2.5.0 and it worked. We saw it working for both modem FW 2.0.0 and 2.0.1.
When we updated SDK to 2.6.1 and modem FW 2.0.1, the...
I am working on nrf52832 based custom board and I want system off sleep and wakeup using GPIO pin state change. For that I have configured MCU standby timeout in sdk_config...
Today I am attempting to set up an MQTT connection from a Thread device to an MQTT server on the Internet (for better or for worse, if this is a terrible idea I'm open to...
i need information on power consumption during advertising and connection in my case its taking too much high current around 1 ma in advertising and 1.5 ma during connection...