We recently encountered an issue with incompatible image partitions being pushed to in-field devices causing soft bricking. refer to this ticket for more information
Problem...
Page 399 of nRF54L15/nRF54L10/nRF54L05 Datasheet v1.0 shows:
CLK = PCLK32M/(2*PRESCALER)
but this formula does not match the values in the examples in Table 46.
I CAN...
Hello Nordic Team,
I am currently working with the nRF52832 on a custom board using nRF Connect SDK v2.9.0. I am implementing OTA DFU using Sysbuild and MCUboot with an...
Hi Team,
I am working on OTA using an external Winbond flash IC (W25Q64) with the nRF52832 controller in NCS SDK version 2.9.2. I have completed all the required configurations...
Hi team,
We are going to kickoff a new project of 2-mic AI recording pen. Good to see we got a very high performance for 54LM20B with DSP/NPU, which might be a very good...
Hello,
We are currently developing a Zigbee product using nRF Connect SDK v2.8.0 . While reviewing the release notes for NCS v2.9.0 , we noticed two critical bug fixes related...
Hi Nordic team,
I have a question regarding the RF matching networks used in the nRF54LM20A-PAAA reference design and in the nRF7002 Expansion Board II (PCA63571).
For...
Two applications using the same softdevice, s110, blinky and beacon from the examples.
Flashing softdevice and beacon successfully.
Replacing beacon app by blinky successfully...
The bootloader in SDK 8.1.0 (at /nRF51_SDK_8.1.0 examples/dfu/bootloader) calls pstorate_register() twice. The first time as part of bootloader_init(), then on bootloader_dfu_start...
hi,
I have implemented a UART to receive network packets from another controller to send it over BLE.
UART config are: 8bits data, 9600 baud rate, no parity, HW flow...
Hello,
I am wondering wether I need to pass regulatory tests when I use the S130 Softdevice together with a 3rd party module such as the one offered by raytac ( www.raytac...
Hi,
So i don't have any experience of working with nrf ble chips, but i was given nrf52 DK and i need to make it work as an iBeacon. So i got the dev board working without...
I'm planning to implement a mesh network, where each node (ble device) also acts as a scanner, detecting BLE advertise messages. The mesh network would then forward the advertisement...
I noted on the release notes for S110 v8 (DRGN-5556, NRFFOETT-986), that enabling/disabling blue_radio_notifications() while the Stack is not idle can cause an assert. Does...
I need something in excess of 5mA output drive. Is there likely to be any problem with connecting two or more GPIO pins in parallel(providing I use OUTSET and OUTCLR to ensure...
Hi,
I have created a project with Keil 5.15
The simply blink app works. Now I want to play with softdevice.
The only problem is... no matter what I do, my hex file always...
Hi ALl
I have permanent error on connect command {0x05, 0x0F, 0x3f, 0xff, 0x40, 0x00 }
When I use security option, with or without PassKey. Return message is 01-03-84...
hey,
so today I updated my NRF Tools... I guess i was using an old version before.
To test our prototypes we have a test fixture where the board is programmed at the...
I'm looking to maximize the throughput using Gazelle on the nRF51.
Assuming zero retransmissions, I believe the theoretical max should be (1/TimeslotPeriod)*PayloadSize...
There is some doubt about the nRF2401L+ RF matching circuit.From the article of <<Tuning_the_nFR24xx_matching_network.pdf>> ,it says "The balun-function is done by the 180...
