I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Hi all,
we are using nRF52810 and SDK 15.3.0
Project is based on central and peripheral concept .
we are facing issue with the peripheral BLE power consumption.
...
We are building a solution for a large OEM where we have BLE tags on inventory trolleys and employees. When the trolley is empty, the BLE tag on the trolley would send a notification...
Hello,
i am working on nRF52832.
i was successfully build a code for scanning without using FreeRTOS
Now i want to use FreeRTOS with my scanning code
But i am not...
Hi ,
i am using ble ancs profile in my project, i was getting internal error (error no 3) while connecting.
the error is being reported by two of the following event handlers...
I have managed to establish a proper TLS connection with the proper credentials, but it seems that TLS session resumption is missing from my implementation since my device...
Hello:
I am now working with nrf5_SDK_for_Mesh_v3.0.0 and I try to implement OTA for mesh dfu. However, I found that the v4.0.0 has a dfu_no_serial_nrf52832_xxAA_s132_7_0_1...
Hello,
I've just recently started learning to develop on the nrf52 platform after 2 years of frustration trying to learn of how to develop on the Nordic platform I finally...
I am trying to set the Lifecycle state of the cryptocell, but it seems like I am having an issue.
I do
/** Enable crypto cell to configure it **/ NRF_CRYPTOCELL->ENABLE...
Hi,
I have fanstel BM833A modules which is NRF52811.
I am using Segger Embedded Studio.
How can i program the module through segger IDE using ST-LINK?
And also i have...
Multi link ble + zigbee multi-protocol testing is currently underway. The main purpose is to test the packet loss rate and throughput of radio time-division multiplexing zigbee...
We've had so many problem with Bluetooth Smart DFU on nRF52832 that I've decided to write a ticket here and ask for help. We've been reading lots of documentation, following...
We want to change the communication speed for each connected peripheral.
*Environment
Peripheral: nrf52832
Central: nrf52840
*Step 1. After the peripheral connects...
Hi all,
My project will use PPI to control COMP of nRF52832, connect Event of COPM and Task of GPIOTE.
Question 1,
How could I get the address of COMP event and use...
