Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I am using nRF SDK v16 with nRF52DK pca10040 board and s112 soft device.
I understand that peer manager can remember each peers' CCCD setting following the bluetooth BLE...
We are evaluating the nRF52832 and have the following questions:
What is the accuracy of the internal ADC voltage reference and the voltage regulators?
Are any of the...
I am using windows 10 and have been able to work with the FOTA sample for the nrf9160 for several months.
I needed to update the SDK from 1.0.0 to 1.1.0. I followed the...
I've been trying to get my 6 Thingy:91s up and running for months now, and the customer is getting really frustrated by the many delays.
I first went through a series of...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1.
Till now I am using ‘ble_app_blinky’ example code, modified to my custom profile and tested On/Off...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
Whether can I call fds_record_update...
During a DFU on SDK15.2 the BLE connection is terminated. The NRF_BL_DFU_INACTIVITY_TIMEOUT_MS is set to 120000.
After 2 minutes, the device still has not reset and started...
Hello,
In the Pin Assignments paragraph of document nRF5340_OPS_v0.5.1 the following pins have no description
B12, A25, B26, J31, T2, K2, H2, G1, F2, D2, A1, A31, AL1...
Dear experts,
My BLE peripheral device uses s112 soft device with nRF52832 and nRF SDK v16 and now the basic data collection and transmission features all work fine with...
We are using the nRF51 bootloader to support DFU over serial. We were able to use the example bootloader as a great reference. We are able to successfully update our app using...
Hello I am trying to develop an application with NRF52833 development board and s113 softdevice.
I want to create a write characteristic which requires 247 ATT-MTU size...
I am trying the ble_app_gls example of nRF SDK v16.0 on nRF52 DK device. The only modification is change s132 to s112.
After download the app to nRF52 device, I can successfully...
So what I want to ask is what is the scan latency during high accuracy and low accuracy?
Also if an insight regarding power consumption can be given would be great (we are...
