after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hello,
I would like to know how to implement middle button click in hid mouse, by middle button click i am referring to scroll wheel click and the function associated with...
Hello!!
Is UICR.CLENR0 register disabled on nrf52SoftDevice?(only nRF51Chip??)
When writing with nRFgoStudio("Enable SoftDeviceProtection" CheckBox is on), the firmware...
Hello,
We are trying to build asset tracker based on a modification of board nrf/boards/arm/nrf9160_pca20035.
Every is good until we tried to enable secure bootloader...
Software : C / GCC - SDK 15.0.0 - SD140 6.0.0 - building on multiple platforms. Hardware : nRF52840-DK (Q1AAC0) - and secondary testing on custom board using the Fanstel BT840...
I have been at this for a few days now, I have had a number of compilation errors that I have had to work through and find solutions for, but I am stumped on this current...
I'm trying to use the low-power comparator.
I've started up the comparator using "lpcomp_init()".
Following that, I wish to have a sample event, and then log the result...
I am trying the example here: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.0.0%2Fble_sdk_app_att_mtu.html
I want to lower the sleep...
Hi,
How do I enable Band 1 on my Thingy 91? On your web-page it seems that your base-band supports Band 1, but when I use the following AT-command AT%XCBAND=? I get the...
we are building some IOT devices for home automation, and things were going quite well since we tried to use our mesh network with two cell phones. we tried with two devices...
Hi.
I am using the NRF (Nrf52840) dongle to operate BLE devices (scan \ read \ write).
Is there a way to do it without the NRF connect application and just sending serial...
Hi,
I used Power Profiler Kit to measure our Custom module's current consumption. Everything worked perfectly.
Then I closed PPK SW and used SDK to flash new SW to one...
Hi,
I have connected nrf9160-dk to my laptop and using nRF connect v 2.6.2 with LTE link monitor application.
I am seeing only UART in green and Modem in Red. I am thinking...
Hello, I am making my first custom board based on nRF52832. I have used a custom antena design (due to PCB layout I did not use reference design). That was the very first...
Hi everyone,
We need your help with a condition that we encountered in our prototype of a nRF52840 that use a ceramic antenna. Our current design is poor and we will have...
