If I try to compile any of the WIFI examples for the Thingy91x I get a RAM overflow error. The only exception to this is the WIFI scanning example. If I build these for any...
Hi everyone,
We’re currently using the nRF9160 module with JIO Nb-IoT SIMs in our devices. Could anyone clarify if any specific actions are needed in the firmware for...
Hi, I was using the BLE online power profiler to determine possible power savings with the nRF54L15DK over the nRF52840 using the zephyr bluetooth broadcaster sample. The...
Hi!
I have been unable to find a single, simple set of instructions for adding MCUboot to a project(toolchain 3.0.0 sdk 3.0.0) that will enable a non-default signing key...
Hi, I am using ncs 3.0.2 and an looking at adding extra .conf files during production. For the app it works fine using --extra-conf, but I can't figure out how to add one...
Hi All, I am trying to write to "adafruit e-link 2.13 Featherwing colour dispaly" from nRF54L15DK running zephyr. With ESP32 i am able to write to the display. But with nRF54L15DK...
Hello
I simply wanted to build an executable from a customized nrfutil. Ran the "pyinstaller nrfutil.spec" and afterwards started the nrfutil.exe from command line. This...
Hi , i want to use SDK 16 with BDS template, is there plugin for ? Or its posssibly to use http://developer.nordicsemi.com/nRF51_bluetooth_development_studio_plugin/ with...
Is this a bug that is resolved in a particular softdevice version? If not, is there more information somewhere on this bug? How do i ensure that my code is robust against...
Are there examples of HW and SW to allow Power Amp, LNA, and TX/RX switch to be connected to the nRF52840_DK?
Or can you tell me what PIN on the chip or connector and pin...
Hello -
We are developing some low power code on the nRF52840-DK, using SDK 15.3.0 on FreeRTOS. I noticed that in the port_cmsys_systick.c file, in the vPortSuppressTicksAndSleep...
I am building a prototype that will use the nrf52840, with limited space. Would making a small pcb antenna or using a chip antenna be better and what is the setup needed for...
Hi,
I would like to measure the voltage generated by a Thermoelectric generator. The voltage vary between -250mV and 250mV depending on the temperature gradient.
If...
I'm looking for alternative xtal's (mhz + rtc) for use on boards where space is very limited.
Silego's GreenCLK3 looks like a great option, though that one is right now...
hi,
I want to use the Bluetooth Low Energy in nRF Connect for desktop. But I have no DK or dongle.
When I use my own development board and the MCU is nRF 52832, it can...
Hi
I am wondering how to choose among different logger mechanisms available in nRF SDK v16.0.
I noticed that some examples doesn't use any logger at all (e.g. blinky...
SDK: 15.3.0 Device: EYSHJNZWZ (nRF52832)
I have cleared the WDT with "nrf_drv_wdt_channel_feed". I want to make sure it is cleared. Which register can be used to confirm...
Hi I am using Keil ARM with JLINK to debug the NRF52832. I can download the flash on the PCBA but when I try to debug step-by step, it only runs on the assembly window but...
Hello ...
Implementing an app for both nRF51822 and nRF52810 and need a long-term clock with 100 Hz counter frequency to timestamp sensor events. By long-term, I mean at...
HI,
I've been looking at the nRF52811 registers for AoA/AoD, and decided to try and at least get CTE enabled on the basic Nordic uart app. I found this post:
https://devzone...
Hello. In acrording to:
How the bridge exchange information between mesh network and mobile device
The bridge using Nordic UART Service to conduct the command/response...
