Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
Hi,
We are in process of picking the right part from Nordic portfolio and are looking at nRF52 Series parts.
We are looking for best performance in below two aspects...
Hello,
SDK: 15.3.0
nRF52840-DK
s140
I have taken the flash_fds_s140_pca10056 example and modified it for our own use. I would like to store versioning information...
Hi Team,
I am working on nrf52840, for openthread application
I flashed cli code built with USB=1 (enables Nrf USB J3), DIAGNOSTIC=1 (enabling factory diagnostics) option...
Hi !
I use SDK:15.3.0 ,Mesh v3.2.0 and have tried official dfu example which is ok.However, When after I enable marco "MESH_FEATURE_PB_GATT_ENABLED=1 MESH_FEATURE_GATT_PROXY_ENABLED...
Hi,
i have designed my custom hardware using BMD-301
i'm able to upload code in bmd-301 using segger embedded studio.
after code uploaded device is not broadcasting...
Hi team, I faced the following problem: there is a custom board with nRF52810 on it, UART is used on this board.
I set up Debug configuration and UART is working OK, but...
Hi,
I am working on a project where I need to send and receive ASCII strings from my Central Device to the Peripheral Device. Before the communication starts there should...
Hi, we have an nRF9160DK (0.8.3) and it does not connect to the nrfcloud.
We have updated to the latest firmware 1.0.0
We only have nb-iot here so we didn't use the iBasis...
Hi Guys
I need your advice. I have a customer that is currently in production with the NRF52840 . They now require direction finding but need a Nordic Evaluation kit to...
Hello,
I am new to Nordic platform, previously i had worked on TI controller.
I have three questions to ask:
1) My firmware consists of four services, each service...
hi,
I am using nRF52832 with KEIL. I want to use version6.0.0 softdevice, but I can't select from KEIL runtime library.
Also, the version that can be downloaded from...
I am trying to change after 10 seconds into non-connectable mode. I am using the below code for initializing:
I want to change mode into non-connectable using this type...
When I use dfu_nrf52832_xxAA_s132_6.1.1.hex, it works all devices updated with blink code as described in dfu_quick_start.md But without any provisioning Process, why? And...
