hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
Hardware: nRF52840, running on dev kit PCA10056
Software: SDK 15.0.0, no soft device
I'm trying to get the POF comparator working, and after struggling in our product...
I just updated my project from SDK 15.3 to 16.0. I am using the nRF52840.
I am not receiving the APP_BUTTON_RELEASE event when waking up from a button press. It used to...
I am trying to the asset tracking application on nRF9160DK and following the steps mentioned in https://devzone.nordicsemi.com/nordic/cellular-iot-guides/b/getting-started...
Hi there,
I have tried to build mqtt_simple but ı got an error says:
#error bsdlib must be run as non-secure firmware. Are you building for the correct board ?
I am...
Dear Support Engineers
I am in the process of designing the automated testing platform for a 52832 based device and would like to test to make sure the components/devices...
Hi, I am trying to test the examples provided in nRF5_SDK_16.0.0 on nRF52840 (PCA20035) thingy91 device. But unfortunately, i didn't see the support files for pca20035. For...
I am using nvs_init(), nvs_read(), nvs_write() calls to store and retrieve user data. Everytime I flash a new image I use the following commands:
# nrfjprog -e -f nRF91...
Hi!
I was wondering about the Receiver Category of the nRF52840 according to EN 300 328. The device should be classified as a category 1, 2 or 3 receiver, based on the...
Hello,
I recently bought a nRF9160 DK version 0.9.0, I did a few software experimentations on it and now I would like to restore the certificates properly.
I followed...
Hello,
I am new to cloud development and was wondering if there is any more documentation or tutorials on how to use the Device APIs for nRF Cloud in addition to the guides...
Dear Team,
why is that the command " AT+CCLK" returns time with 2hours of difference? How should one compensate?
AT+CCLK? +CCLK: "19/07/19,19:57:30+08" OK AT+CCLK? ...
Using a multimeter and a Thingy:91 I've measured the current to
The nrf9160 ( infocenter.nordicsemi.com/index.jsp
The nrf52840
The total (measured between battery...
Hi,
The following article describes how to perform serial programming of nRF9160 on Thingy91: https://devzone.nordicsemi.com/nordic/cellular-iot-guides/b/getting-started...
I connected to nrfcloud using a SIM card from iBasis and the asset tracker example.
Is it possible to connect to nrfcloud using a SIM card from another vendor? (in my case...
We are trying to get the ble_app_uart project to run on an nRF52811 using Soft Device 113, since our application will require the LE Data Packet Length Extension. We started...
