I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I've used the example in examples/peripheral/gpiote to count edges of a WATCHDOG pin from a different MCU:
After starting the timer I want to periodically get the...
Hello,
I am using MDBT42Q nrf52832 module, SDK 15.3.0 in Segger Studio IDE,on Win10.
I am configuring my device to advertise for 20 min, 5 min fast advertising and 15...
Hi all
I am able to do start loopback using the example of UART.
But how to send data to external modules ( like ESP32) via UART from nRF9160.
I tried this example Thread...
Hi,
I want use the BLE DFU (In SDK11) to implement software upgrade to my unit.
I want the unit to support BLE and External SPI FLASH (on board) upgrade.
My unit got...
Hi
In the mqtt_simple example there is a line " modem_configure(); " which establishes the LTE Link connection. If connecting the LTE link is not possible (for example no...
I have now removed all my experimental code and have returned to the more or less original verion of the main.c for assec_tracker, but still the application seems to be stuck...
We are using the Nordic nRF52840 on our current design. Currently, I am using nRF Toolbox -UART app on my
mobile phone to send data via 9 buttons available on the App. Everything...
I am trying to read the data of an MQ-6 sensor, which is its gas sensor, but the data I receive is not from the reading by the values it shows, if you know how to do it or...
Hi,
When the bootloader address resolves to something invalid, fds_init will hardfault. I think it should have some check and return a nice error code instead.
See an...
Hi,
I want to disable all four buttons to my rigado bmd 300 evaluation kit (pca10040 is the board config. the same as nrf52 DK ) in project ble_app_uart
I have tried to...
I'm powering an nrf52810 with a 3.3V regulator. I understand the internal LDO powers the system at 1.3 V. Are the GPIO pins and other peripheral devices outputting 3.3V for...
Hi
When I select the Generic Level server model and try to bind the app key I get an invalid model Error. I am using the nRF Mesh android app.
This might be relevant or...
Dear Nordic Support,
I am using ble_nus service on nRF52840 (BMD-340-A-R) + Raspberry Pi 3B+ ( https://github.com/IanHarvey/bluepy ). The nRF52840 is the peripheral and...
Hi,
I would like to know the I2C bus capacitance for the nrf52840. Do someone have the information please ?
My slave components are compliant for 400Khz and VDD is 3.3V...
