Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello,
SDK: 15.3.0
nRF52840-DK
IDE: SES
Example: flash_fds_s140_pca10056
Example Location: nRF-SDK\examples\peripheral\flash_fds\pca10056\s140\ses
Example Documentation...
It builds OK and I can flash the hex file using nRF connect Programmer. But I need to debug the code but I have not found a way to upload the code and break at main() entry...
Hi,
As we all know that nRF52811 support AoA/AoD feature. But I have not found example in corresponding SDK( nRF5_SDK_15.3.0_59ac345 ) . If you have example of AoA/AoD,...
If you look at the secure bootloader example the nrf_bootloader_init(...) never return to main scope unless an error occurs.
Everything is handled inside this function even...
The " 5.3.6.8 Reset behavior " table in nRF52840 Product Specification v1.1 mentions that WDT reset does reset the WDT itself.
I'm trying to reconfigure the WDT after a...
Hello,
I am using HC-SR04 ultrasonic sensor and nrf52840dk. To measure the distance I have to find out for how long the ECHO pin of the sensor remains high.
for that I...
On my old Wondows10 development computer, all worked OK.
In a brand new Windows10 laptop, all up to this point installs/verifies fine using nRF Connect.
I cannot find...
Hello, I'm making a PCB project with nrf52832 and I want to use my debuggers only 2 pins(SWDCLK and SWDIO) to debug it. I have J-Link Edu, but I wonder if I can use it with...
Hi, All.
I' m studying nRF52832.
I have a question about example "ble_app_uart".
I m trying to send to smartphone using function "printf()".
Uart pins(RX, TX) are...
Hi everybody! I have a code running excellently on my nRF52840 DK. I would like to make it run on my nRF52840 dongle. What should I change in my SEGGER project? Can anybody...
I am building a project which requires accelerometer data from the LIS3DH accelerometer be read and then transmitted over bluetooth. I have successfully setup bluetooth transmission...
Hi,
For my project I need to receive 9 bytes of data from our main board. This data gets send using UART.
By looking at the pin diagram I could not find specific pins...
Hello,
I am running nRF Connect for Desktop v3.2.0 on Win10 64-bit machine. Everytime I launch an applet, such as Power Profiler, I get a new blank window and nothing happens...
Hi, I am having a problem changing information advertised by the Beacon while the application is running. I started with the app_ble_template example and added Information...
