Hello,
I have a custom PCB with the nRF5340 chip. I’m able to flash the board using a J-Link. I’d like to rename the device so that it advertises a specific Bluetooth name...
Hello,
We are currently using the nrf52840 for development using Zephyr v3.7.99-ncs1 .
We want to use the UART in low power mode and therefore, we have used the zephyr...
Greetings!
Briefly summarized: I am trying to generate SPDX files for our project, but I hit some roadblocks while running the west spdx command. I found a way to workaround...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
I purchased a SIM data from ILIAD and I am trying to connect to network, but the AT command AT+CEREG? : +CEREG: 0,4 instead of 0,5 as I expect.
The lte_lc_connect_async...
Hi I am using an nRF54L15 with an external watch crystal. I have notice that depending on the manufacturer of the crystal I have to use a different internal load capacitor...
I am using the `mcumgr` subsys to enable the DFU (Device Firmware Update) capabilities in a custom device that also features a custom (non mcuboot) bootloader. In order to...
We are using nRF51822 in our custom board.
We just remain two pin ------ SCLK and SWDIO
Can we programming by STLink ?
what's the step?
1.using nrfgo studio to programming...
I tried setting the name as AT+NAME=LGS\r\n
When I send AT+NAME?\r\n, I do read back the new name, i.e. LGS.
However, the bluetooth host continues to see my device as...
Hello, I am using the sim card that comes with the Thingy91 in Sweden, it works well but every time I reflash the thingy with a new version of my application it takes several...
I went through each of the steps for upgrading the thingy91 modem firmware -> application firmware -> 52840 firmware but when I look at the lte link monitor it looks like...
Device: nRF52832, SD132v7.0.1, NRFSDK 16.0.0
Host: nRF52840 USB BLE dongle, pc-ble-driver-py 0.14.1, Python script, Linux
We're developing a device that's a BLE Peripheral...
Hi, I am looking for any suggestions on heart rate sensors i can use that would easily integrate with the nrf52832. I am looking to get a finalized output from the heart rate...
Hi I have a few questions about bluetooth 5.1 and the CTE packets that it transmits.
1. I know that there is a physical difference in the hardware of a Bluetooth 5.0 chip...
Hi,
I have nRF52840 dongle PCA10059. I want to use dongle as sniffer.
So how and what hex file and other thing i need to do ? To use dongle work as sniffer.
Hi,
I have been trying to get UART working properly on my custom board but also on nRF9160 DK. I'm using only UART_0.
With CONFIG_USE_AT_HOST and without any uart code...
tag v1.1.0 (have done west update) using SES 4.30c as suggested by nrf connect Compiled and flashed using SES modem firmware mfw_nrf9160_1.1.1 downloaded and updated the certificate...
I have developed a ble5 long range and meshing product but my life is way to short. using 2-3.6v batteries in parallel and only getting 2 months life in my battery calculations...
Hello everyone !!
While in test, I use Phone Mi Max 2 communicate with NRF52, sometime NRF52 send to Phone but Phone didn't received. I used sniffer and see packets to be...
Hi !
We are planning to add sensor device over Mesh network.
This sensor device will share Room Temperature, Outside Temperature, Humidity, ambient light and movement...
